NTH - Management Information System

National Test House (ER), Kolkata

Block-C.P, Sector-V, Salt Lake City, Kolkata, West Bengal - 700091, Kolkata, Kolkata, West Bengal, 700091

- nthsal-wb[at]nic[dot]in

Scope List

Reset

1145 Results

S.No.

Standard No.

Product

Testing Charges (Excl. Of Taxes)

CUSTOM/POLYUTHERANE SPRING POST/2024 - POLYUTHERANE SPRING POST

POLYUTHERANE SPRING POST

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1.0 (Material Identification)	4000.0
2.0 (Filler Content)	2000.0
3.0 (Density)	1000.0
4.0 (Melting Point)	1000.0
5.0 (Compressive Strength Horizontally)	2000.0
6.0 (Tensile Strength)	2000.0
7.0 (Elongation at Break)	1000.0
8.0 (UV Resistant (24 Hrs.))	1200.0

RDSO SPECIFICATION No. M&C/ PCN/ 100/ 2018 (2018) - FULL GLOSS POLYURETHANE ENAMEL (TWO PACK)

FULL GLOSS POLYURETHANE ENAMEL (TWO PACK)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Identification of polyisocyanates)	1200.0
2 (Drying time a) Surface dry b) Hard dry c) Hard dry at 70 Deg. C)	3600.0
3 (Consistency)	1200.0
4 (Finish)	1200.0
5 (Colour)	1200.0
6 (Dry film thickness)	1200.0
7 (Volume solids)	1200.0
8 (Scratch hardness (1.5 Kg Load))	1200.0
9 (Flexibility & Adhesion (6.25 mm mandrel))	1200.0
10 (Flash point (a) Component ‘A’ (b) Component ‘B’)	2400.0
11 (Fineness of Grind)	1200.0
12 (Pot life (After induction time) at a) 27±2°C b)40±2ºC)	1500.0
13 (Gloss at 60° angle of incidence)	1200.0
14 (Mass in Kg/10 litres)	1200.0
15 (Keeping properties)	5000.0
16 (Theoretical spreading rate)	2000.0
17 (% poly isocyanate by mass, in hardener)	3000.0
18 (Viscosity (Efflux time by Ford cup No.4) of paint i.e. mix. Of two components at 27± 2 °C in Supply condition)	1200.0
19 (Accelerated Tests (a) Resistance to 30% Sulphuric acid (weight by volume) (b) Resistance to 20% caustic potash (weight by volume) (c) Resistance to oil (d) Resistance to solvents (e) Resistance to water)	7200.0
20 (Durability Tests Accelerated weathering test)	37500.0
RDSO SPECIFICATION No. M&C/ PCN/ 100/ 2018 (Please refer annexure for test result (Table 1. Full Gloss Polyurethane Enamel Two Pack) Except parameter Unreacted monomer)	21000.0
22 (Abrasion resistance-1000 Cycle)	5000.0

RDSO Specification No. M&C/PCN/100/2018 - POLYURETHANE SURFACER (TWOPACK)

POLYURETHANE SURFACER (TWOPACK)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Drying time a) Surface dry b) Hard dry c) Hard dry at 70°C)	3600.0
2 (Consistency)	1200.0
3 (Finish)	1200.0
4 (Colour)	1200.0
5 (Dry film thickness)	1200.0
6 (Volume solids, %)	2000.0
7 (Scratch hardness (1.5Kg Load))	1200.0
8 (Flexibility & Adhesion (6.25 mm mandrel))	1200.0
9 (Flashpoint a) Component ‘A’ b) Component ‘B’)	2400.0
10 (Fineness of Grind)	1200.0
11 (Pot life (After induction time) i) 27±2°C ii) 40±2°C)	1500.0
12 (Mass in Kg/10 litres)	1200.0
13 (Keeping properties)	2000.0
14 (Theoretical spreading rate)	2000.0
15 (Viscosity (Efflux time by Ford cup No.4) of paint i.e. mix of two components at 27± 2 °C in Supply condition)	1200.0

NTH/ER/RPPT/HDPE PIPE INSPECTION-2024 - INSPECTION OF HDPE PIPES

INSPECTION OF HDPE PIPES

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Firm's request (Inspection Report)	17000.0

RDSO SPECIFICATION M&C/PCN/100/2018 PUTTY - UNSATURATED POLYESTER BASE KNIFING PUTTY (TWO PACK)

UNSATURATED POLYESTER BASE KNIFING PUTTY (TWO PACK)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Drying time: a)Surface dry b) Hard dry c)Hard dry time at 70 Deg. C)	3600.0
2 (Consistency)	1200.0
3 (Stopping properties)	2000.0
4 (Rubbing properties)	2000.0
5 (Hold out Property)	2000.0
6 (Adhesion & Compatibility of Paint System)	2000.0
7 (Pot life ,at 27±2 Deg. C)	1500.0
8 (% solids)	1200.0
9 (Keeping properties)	5000.0

Custom Paint finishing Aluminium paint Heat resistance - Custom Paint finishing Aluminium paint Heat resistance

Custom Paint finishing Aluminium paint Heat resistance

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Preliminary Examination)	1000.0
2 (Consistency)	1000.0
3 (Flash Point (Abel))	1000.0
4 (Efflux time at 27(+/-)5 Deg.C ( for first 50 ml))	1000.0
5 (Application Properties & Finish)	1000.0
6 (Covering Power)	1000.0
7 (Drying time (i) Surface dry)	1000.0
8 (Drying time (ii) Hard dry)	1000.0
9 (Colour)	1000.0
10 (Flexibility & Adhesion (Bend Test))	1000.0
11 (Scratch Hardness)	1000.0
12 (Volatile matter)	1000.0
13 (Resistance to high Temperature (a) At 300 Deg.C For 4 Hours)	1000.0
14 (Resistance to high Temperature (b) At 400 Deg.C For 1 Hour)	1000.0
15 (Resistance to high Temperature (c) At 600 Deg.C For 1 Hour)	1000.0

Custom Paint RFU Finishing various shades - Custom Paint RFU Finishing various shades

Custom Paint RFU Finishing various shades

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
20 (Durability Test (25 days Outdoor Exposure Then 96 hours salt Spray))	5000.0
19 (Accelerated Storage stability)	3000.0
15 (Resistance to Salt Spary (96 hrs))	4800.0
18 (Presence of Rosin Derivative)	1000.0
17 (Non-volatile Content)	1000.0
16 (Flash Point (Abel))	1000.0
14 (Stripping Test)	1000.0
13 (Scratch Hardness)	1000.0
12 (Flexibility & Adhesion (Bend Test))	1000.0
11 (Wet Opacity)	1500.0
10 (Colour)	1000.0
9 (Gloss)	1000.0
8 (Fineness of Grind)	1000.0
7 (Finish)	1000.0
6 (Drying time (iii) Tack free dry)	1000.0
5 (Drying time (ii) Hard dry)	1000.0
4 (Drying time (i) Surface dry)	1000.0
3 (Relative consistency at 27 deg. C)	1000.0
2 (Consistency)	1000.0
1 (Preliminary Examination)	1000.0
33 (Natural outdoor weathering)	3000.0
32 (Resistance to warm water (45 ± 3 °C for 4 hours))	1200.0
31 (Resistance to heat (after air drying for 48 hours) Except White)	1200.0
30 (Resistance to petrol -benzol mixture)	1200.0
29 (Resistance to Alkali)	1500.0
28 (Resistance to Acid)	1500.0
27 (Mass in Kg/10 litres)	1200.0
26 (Accelerated Storage Stability test)	3000.0
25 (Lead Restriction total lead compound as PbO expressed as % of dry pigment)	1000.0
24 (Water content, %)	1200.0
23 (Resistance to Humidity under condition of condensation)	12000.0
22 (Application)	1200.0
21 (Efflux time (Ford Cup No. 4) at 30 ±1 Deg. C)	1200.0
33 (Natural outdoor weathering)	3000.0

MMDTS 18034 (Rev. 04) (2019) - Technical Specification for PU based Wet -On- Wet Applicable on Exterior Painting System for LHB Types Coaches.

Technical Specification for PU based Wet -On- Wet Applicable on Exterior Painting System for LHB Types Coaches.

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 ((Anti Graffiti test ASTM D-6578))	5000.0

CUSTOM PAINT ONSITE TESTING-1 (2024) - CUSTOM PAINT ONSITE TESTING-1

CUSTOM PAINT ONSITE TESTING-1

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Distinctness of Image (DOI))	10000.0

100

IRC 105 (2019) - SPECIFICATIONS FOR DENSE BITUMINOUS MACADAM AND BITUMINOUS CONCRETE FOR AIRFIELD PAVEMENTS

SPECIFICATIONS FOR DENSE BITUMINOUS MACADAM AND BITUMINOUS CONCRETE FOR AIRFIELD PAVEMENTS

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Table 3.5 (Durability [ Soundness (Sodium sulphate )], %)	2000.0
Table 3.5 (Durability [Soundness (Magnesium or Sodium Sulphate )], %)	2000.0
Table 3.5 (Particle Shape (Combined Flakiness and Elongation Index), %)	3000.0
Table 3.5 (Strength [Los Angeles Abrasion Value], %)	1500.0
Table 3.5 (Strength [Aggregate Impact Value], %)	1500.0
2 (Density of DAC (On lines of ASTM D 2726))	2000.0
2 (Density of DBM (On lines of ASTM D 2726))	2000.0

101

ASTM B117 Salt spray - ASTM B 117 Salt spray Test For 96 hrs

ASTM B 117 Salt spray Test For 96 hrs

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found

102

Custom/Mech/2022 (2022) - Specification for Customer Test request.

Specification for Customer Test request.

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
0 (Chemical Composition)	4000.0
0 (Mass of Zinc Coating)	4000.0
0 (Test results Chemical as per annexure)	10000.0
0 (Test results as per annexure)	61200.0
8 (Dimensions)	2500.0
0 (Yield Stress, N/mm2)	1000.0
0 (Percent Elongation)	1000.0
0 (Bend test)	1000.0
0 (Proof Load)	3000.0
0 (Load test of Wedge on the lines of IS 14268)	3000.0
0 (Salt Spray test, 1440 Hrs.)	60000.0
0 (Tensile strength test, N/mm2)	3000.0
0 (Decarburization test)	3000.0
0 (Load Test)	5000.0
0 (Dimensions of Bolt Nut and washer)	2000.0
0 (Chemical Analysis(SS 304/SS 316) of Bolt, Nut and washers)	8000.0
M1 (Shear Strength test, MPa)	3000.0
C2 (Brinell/ Vickers/ Rockwell Hardness)	2000.0
C3 (Tensile Strength (MPa))	1000.0
0 (Impact test, J)	3000.0
0 (Microstructure analysis)	3000.0
0 (Percent Reduction of Area)	1000.0
0 (Breaking Load)	3000.0
0 (Test results)	10000.0
0 (Compression Test)	3000.0
0 (Uniformity of Coating)	2000.0
0 (Coating Thickness)	2000.0
0 (Adhesion Test)	1000.0

103

CUSTOM/Aluminium Polymer Composites (APC) /2024 - CUSTOM/Aluminum Polymer Composites (APC) /2024

CUSTOM/Aluminum Polymer Composites (APC) /2024

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1.0 (Density)	1000.0
2.0 (Water Absorption)	1000.0
3.0 (Tensile Strength)	2000.0
4.0 (Tensile Elongation)	1000.0
5.0 (Flexural Strength)	2000.0
6.0 (Flexural Modulus)	2000.0
7.0 (Resistance to wet Heat)	2000.0
8.0 (Stain Resistance)	5000.0
9.0 (Wear and Clanability)	2000.0
10.0 (Light Resistance (Xenon Arc).)	3000.0

104

MDTS - 46303 (2016) - Schedule of Technical Requirements For Composite Decorative Glass Fabric Reinforced Plastic (DGFRP)

Schedule of Technical Requirements For Composite Decorative Glass Fabric Reinforced Plastic (DGFRP)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
3.2 (Density)	1000.0
3.2 (Tensile Strength Along the Length)	1000.0
3.2 (Tensile Strength Along the Width)	1000.0
3.2 (Breaking Strength along the length)	1000.0
3.2 (Breaking Strength along the Width)	1000.0
3.2 (Water Absorption)	1000.0
3.2 (Drop Impact Test)	1000.0
3.2 (Resistance to staining rating scale)	5000.0
3.2 (Resistance to Color Change in Xenon Arch Light)	3000.0
3.2 (Resistance to Surface Wear)	5000.0
3.2 (Resistance to Immersion in Boiling Water -Appearance)	500.0
3.2 (Resistance to Immersion in Boiling Water- Increase in Thickness)	1000.0
3.2 (Resistance to immersion in boiling Water- De-lamination)	500.0
3.2 (Resistance To Surface Wear)	5000.0

105

CUSTOM/JUTE SAND SNAKE/2024 - CUSTOM/JUTE SAND SNAKE/2024

CUSTOM/JUTE SAND SNAKE/2024

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1.0 (Mass)	1000.0
2.0 (Thread Used)	1000.0
3.0 (Construction)	1000.0
4.0 (Length)	500.0
5.0 (Width)	500.0

106

Custom - Diesel

Diesel

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Density)	1200.0
2 (Flash point)	1200.0

107

IS 17048 (2018) - Halogen Free Flame Retardant (HFFR) Cables for Working Voltages up to and including 1100 Volts-Specification

Halogen Free Flame Retardant (HFFR) Cables for Working Voltages up to and including 1100 Volts-Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
15.6 Table 2 (iii) (a) (i) (Conductor Resistance Test)	1500.0
15.6 Table 2 (iii) (a) (ii) (Annealing Test (For copper))	1000.0
15.6 Table 2 (iii) (b) (Test for Overall Dimensions and Thickness of Insulation and Sheath)	1000.0
15.6 Table 2 (iii) (c) (iii) (Insulation Resistance Test)	2000.0
15.6 Table 2 (iii) (c) (ii) or (iii) (f) (i) (High Voltage Test)	1500.0
15.6 Table 2 (ii) (f) (Tensile strength and elongation at break)	1500.0
15.6 Table 2 (iii) (c) (xiii) & (iii) (f) (v) (Flame Retardant Test)	3000.0
15.6 Table 2 (iii) (f) (ii) (Flammability test)	500.0
- (Test on 2nd Core)	2000.0
- (Test on 3rd Core)	2000.0
- (Test on 4th Core)	2000.0

108

IS 9537 : Part 2 (1981) - Specification for conduits for electrical installations: Part 2 rigid steel conduits

Specification for conduits for electrical installations: Part 2 rigid steel conduits

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
9.2 (Bending Test (With Seam on the Outside of flank))	500.0
9.2 (Bending Test (With Seam on the flank))	500.0
13 (External Influence Test (With Seam on the flank))	1000.0
13 (External Influence Test (With Seam on the Outside of the Bend))	1000.0
9.3 (Compression Test)	3000.0
7 (Wall thickness)	500.0
7 (Outside Diameter)	500.0
7.2 (Checking the Minimum outside diameter.)	750.0
7.2 (Checking the Maximum outside diameter)	750.0

109

CUSTOM/SHARPENER/2024 - Material

Material

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1.0 (Material)	1000.0

110

CUSTOM/CRAYONS/2024 - CUSTOM/CRAYONS/2024

CUSTOM/CRAYONS/2024

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1.0 (No. of Shades)	500.0
2.0 (Material)	500.0
3.0 (Colour)	500.0
4.0 (Crayons Shape)	500.0
5.0 (Crayon length)	1000.0
6.0 (Crayon Diameter)	1000.0

111

CUSTOM/ERASER/2024 - CUSTOM/ERASER/2024

CUSTOM/ERASER/2024

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1.0 (Material)	1000.0
2.0 (Dimension)	1000.0

112

CUSTOM/PENCIL/2024 - CUSTOM/PENCIL/2024

CUSTOM/PENCIL/2024

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1.0 (Material)	1000.0
2.0 (Length)	1000.0

113

CUSTOM/PENCIL BOX/2024 - CUSTOM/PENCIL BOX/2024

CUSTOM/PENCIL BOX/2024

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1.0 (Material)	1000.0
2.0 (Type)	1000.0
3.0 (Dimension)	1000.0
4.0 (Pattern)	500.0
5.0 (Weight)	1000.0

114

ASTM D 1653 - Water Vapor Transmission

Water Vapor Transmission

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Water Vapor Transmission)	5000.0

115

Custom Specification for Electrical Testing Laboratory ,NTH(ER),Salt Lake - Custom Specification for Electrical Testing Laboratory ,NTH(ER),Salt Lake

Custom Specification for Electrical Testing Laboratory ,NTH(ER),Salt Lake

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
A10 (Custom Specification 10)	100000.0
A1 (Custom Specification 1)	10000.0
A2 (Custom Specification 2)	20000.0
A7 (Custom Specification 7)	70000.0
A5 (Custom Specification-A5)	50000.0

116

ND Custom 10 (2024) - Load Bearing Capacity for RCPC Slabs

Load Bearing Capacity for RCPC Slabs

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Firm's Requirement (Load Bearing Capacity Test)	3000.0

117

IS IS 1708 : Part 18 (1986) - Timber

Timber

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found

118

IS IS 1708 : Part 17 (1986) - Timber

Timber

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found

119

IS IS 1708 : Part 16 (1986) - Timber

Timber

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found

120

IS IS 1708 : Part 15 (1986) - Timber

Timber

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
0 (Nail and screw holding power)	3000.0

First
Prev
3
4
5
6
Next
Last