NTH - Management Information System

National Test House (SR), Chennai

CSIR Road, Tharamani, Chennai - 600113, Chennai, Chennai, Tamil Nadu, 600113

9444380435 directornthsr[at]nth[dot]gov[dot]in

Scope List

Reset

487 Results

S.No.

Standard No.

Product

Testing Charges (Excl. Of Taxes)

Rubber NABL-2023-26 - Rubber NABL-2023-26

Rubber NABL-2023-26

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Density / Sp. Gravity)	1000.0
2 (Elongation at Break)	1000.0
3 (Tensile Strength)	2000.0

CUSTOM/SR/CHEMICAL (2024) - Custom Standard for Water Samples collected during Social Activity : Mobile Water Testing

Custom Standard for Water Samples collected during Social Activity : Mobile Water Testing

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Test results for Chemical analysis in Annexure (NON-NABL))	-
Micro-1 (E. coli or thermotolerant coliform bacteria)	-
Micro-2 (Total coliform bacteria)	-

303 (2024) - Plywood for General Purpose

Plywood for General Purpose

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
8.1 (Length, in mm)	500.0
8.1 (Width, in mm)	500.0
8.2 (Thickness, in mm)	500.0
8.3 (Squareness, in mm/m)	500.0
8.3 (Edge Straightness, in mm/m)	500.0
5 (Classification by Appearance)	1000.0
9 (Workmanship and finish,)	1000.0
11.3.1 (a) (Glue Adhesion - Water Resistance Test)	2000.0
11.3.1 (b) (Glue Adhesion Test - Water Resistance Test - BWR Grade)	2000.0
11.3.1 cb) (Glue Adhesion Test - Water Resistance Test - BWP Grade)	2000.0
11.3.2 (Mycological Test)	1500.0
11.4 (Moisture Content, in %)	1000.0
11.5 (Static Bending Strength (Modulus of Rupture -Along), in N/mm^2)	1000.0
11.5 (Static Bending Strength (Modulus of Rupture - Across), in N/mm^2)	1000.0
11.5 (Static Bending Strength (Modulus of Elasticity-Along), in N/mm^2)	1000.0
11.5 (Static Bending Strength (Modulus of Elasticity- Across), in N/mm^2)	1000.0
11.6 (Formaldehyde Content Test, in mg/100g)	3000.0

CUS/SR/MECH-56 (2025) - Thread Locker

Thread Locker

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1.0 (Proof Load, kN)	3000.0
2.0 (Hardness, HRC)	2000.0

IS/IEC 61439-1 (2020) - Low-voltage switchgear and controlgear assemblies Part 1: General rules

Low-voltage switchgear and controlgear assemblies Part 1: General rules

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Cl No. 10.10 (Temperature-rise)	30000.0
Cl No. 10.9 (Dielectric properties (High Voltage Test))	20000.0

8623-1:(1993) - Low-Voltage Switchgear and Control gear Assemblies, Part 1: Requirements for Type-Tested and Partially Type-Tested Assemblies [ETD 7: Low Voltage Switchgear and Control gear]

Low-Voltage Switchgear and Control gear Assemblies, Part 1: Requirements for Type-Tested and Partially Type-Tested Assemblies [ETD 7: Low Voltage Switchgear and Control gear]

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
8.2.1.3 (Tempreture rise test)	20000.0
8.2.2 (Verification of dielectric properties)	10000.0
8.3.4 (Verification of insulation resistance)	10000.0

IS 6419 (1996) - Welding rods and bare electrodes for gas shielded arc welding of structural steel - Specification (First Revision)

Welding rods and bare electrodes for gas shielded arc welding of structural steel - Specification (First Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
14.3.3 (All weld Impact test)	3000.0
14.3.2 (Ultimate Tensile Strength (All Weld Metal Mechanical Test ))	3000.0
14.3.2 (Yeild Strength (All Weld Metal Mechanical Test ))	500.0
14.3.2 (Percent Elongation (All Weld Metal Mechanical Test ))	-
14.3.1 (Preparation of Weld assembly)	5000.0
14.2 (Radiography Test)	1000.0
10.2.3 (Helix)	500.0
10.2.2 (Cast)	500.0
10.2.1 (Temper)	1000.0
10.1 (Finish)	500.0
8.3 (Dimension of Coils)	500.0
8.2 (Dimension of Rims)	500.0
8.1 (Dimension of Spools)	500.0
10.1 (Finish)	500.0
5 (Diameter of Wire)	500.0
6 (Reels of Wire)	500.0
7 (Reeling Conditions)	500.0
14.1 (Copper)	500.0
14.1 (Vanadium)	500.0
14.1 (Molybdenum)	500.0
14.1 (Chromium)	500.0
14.1 (Nickel)	500.0
14.1 (Phosphorus)	500.0
14.1 (Sulphur)	500.0
14.1 (Manganese)	500.0
14.1 (Silicon)	500.0
14.1 (Carbon)	500.0
14.1 (Aluminium)	500.0
14.1 (Zirconium)	500.0
14.1 (Titanium)	500.0

IS 2556(Part 15):2024 - Vitreous China Sanitary Appliances-Specification ( Part 15)-Specific requirements of Universal Water Closets

Vitreous China Sanitary Appliances-Specification ( Part 15)-Specific requirements of Universal Water Closets

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
3 (General requirements-IS 2556(1))	3000.0
4 (Sizes)	1000.0
5 (Dimensions and Tolerances)	2000.0
6 (Construction)	1000.0
7 (Finish)	1000.0
8.2 (Flushing Test-Toilet Paper Test)	1000.0
8.3 (Flushing Test-Smudge Test)	1000.0
8.4 (Flushing Test-Holding Capacity Test)	1000.0
8.5.1 (Single ball Test)	1000.0
8.5.2 (Fifty Ball Test)	1000.0
8.6 (Saw Dust Test)	1000.0
8.7 (Splash Test)	1000.0
9 (Load bearing Test)	1000.0

IS 15965 : 2012 (2012) - Pre-painted Aluminium Zinc Alloy Metallic Coated Steel Strip and Sheet (Plain)

Pre-painted Aluminium Zinc Alloy Metallic Coated Steel Strip and Sheet (Plain)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
3.3 (Total Coated Thickness (As received condition), mm)	1000.0
8 (Tensile Strength (As per IS 15961), MPa)	1000.0
8 (Yield Strength (As per IS 15961), MPa)	1000.0
8 (% Elongation (As per IS 15961), %)	1000.0
7.1 (Mass of Coating (Both sides), g/m²)	2000.0
5 (Chemical composition (As per IS 513), % by mass)	2500.0

IS 9857:1990 (1990) - Welding Cable Specification

Welding Cable Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found

IS 9143:1979 - Indian standard-Method for the determination of Unconfined Compressive strength of Rock materials

Indian standard-Method for the determination of Unconfined Compressive strength of Rock materials

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6 (Unconfined Compressive strength /Uniaxial Compressive strength-N/ Sq mm)	5000.0

IS 1481 (2024) - Specification for metric steel scales for engineers (First Revision)

Specification for metric steel scales for engineers (First Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4 (Length)	1200.0

RDSO/2007/GE:0014 November 2009 (November 2009) - Guidelines and Specifications for Design of Formation for Heavy Axle Load (RDSO/2007/GE:0014 )

Guidelines and Specifications for Design of Formation for Heavy Axle Load (RDSO/2007/GE:0014 )

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
12.1(i-a) (The uniformity coefficient (Cu) IS 2720-1 (1983)/IS 1498 (1970))	1500.0
12.1.(i-b) (The Coefficient of Curvature (Cc) IS 2720-1 (1983)/IS 1498 (1970))	1500.0
12.1.(ii) (Los Angeles Abrasion Value (IS 2386(4):1963))	1500.0
12.2 (Sieve Analysis/Grading Percentage /Grain size distribution [IS 2720 (Part 4)])	5000.0

IS 1586 : Part 1 (2018) - Metallic materials - Rockwell hardness test: Part 1 test method (Fifth Revision)

Metallic materials - Rockwell hardness test: Part 1 test method (Fifth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Hardness)	2000.0

14255 (1995) - Aerial Bunched Cables for working voltages up to and including 1100 Volts-Reaffirmed 2020 specification

Aerial Bunched Cables for working voltages up to and including 1100 Volts-Reaffirmed 2020 specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
10.1 sl no 1(a)(i), 10.2 (a) (Tensile Test on phase/ street light conductor)	1000.0
10.1 sl no 1(a)(ii), 10.2 (b) (Wrapping Test on phase/ street light conductor)	500.0
10.1 sl no 1(a)(iii) (Resistance Test on phase/ street light conductor)	2000.0
10.1 sl no 1(b)(i) ,10.2 sl no(c) (Test on messenger conductor Breaking load)	1000.0
10.1 sl no 1(b)(ii), 10.2 (d) (Test on messenger conductor Elongation test)	1500.0
10.1 sl no 1(c)(i),10.2 (g) (Physical test for XLPE insulation Tensile strength and elongation at break)	1500.0
10.1 sl no 1(c)(ii) (Physical test for XLPE insulation Ageing in air oven)	2000.0
10.1 sl no 1(c)(iii),10.2(h) (Physical test for XLPE insulation Hot set test)	2000.0
10.1 sl no 1(c)(iv) (Physical test for XLPE insulation Shrinkage)	1000.0
10.1 sl no 1(c)(v) (Physical test for XLPE insulation Water absorption test)	1000.0
10.1 sl no 1(d)(i) (Physical test for PE insulation Tensile strength and elongation at break)	1500.0
10.1 sl no 1(d)(iv) (Physical test for PE insulation Vicat softening point)	1000.0
10.1 sl no 1(d)(ii) (Physical test for PE insulation Melt flow index)	1000.0
10.1 sl no 1(d)(v) (Physical test for PE insulation Environment stress cracking)	1500.0
10.1 sl no 1(e),10.2(f) (Test for thickness of insulation)	1500.0
10.1 sl no 1(f),10.2(j) (Insulation resistance (Volume Resistivity) test)	1500.0
10.1 sl no 1(g),10.2(k) (High Voltage test)	1500.0
10.2 (e) (Conductor resistance test)	2000.0
Test on 2nd core (Test on 2nd core)	2000.0
Test on 3rd core (Test on 3rd core)	2000.0
Test on 4th core (Test on 4th core)	2000.0
10.1 sl no 1(b)(iii) (Resistance test on messenger conductor)	1000.0

IS 2026 : Part 1 (2011) - Power Transformers: Part 1 General (Second Revision)

Power Transformers: Part 1 General (Second Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
10.1.2(a) (Temp Rise)	7000.0
10.1) c ) (Loss % Impedence)	20000.0
10.1.1(e) (Voltage)	9600.0
10.1.1(e) (Voltage)	6400.0
10.1.1(d) (Loss Current)	12800.0
10.1.2(b) (Lightning lmpulse Voltage test, Chopped impulse voltage test, Multi chopped irnpulse voltage test)	500000.0
10.1.2(b) (Lightning lmpulse Voltage test, Chopped impulse voltage test, Multi chopped irnpulse voltage test)	85000.0
10.1.2(b) (Lightning lmpulse Voltage test, Chopped impulse voltage test, Multi chopped irnpulse voltage test)	130000.0
10.1.2(b) (Lightning lmpulse Voltage test, Chopped impulse voltage test, Multi chopped irnpulse voltage test)	140000.0
10.1.2(b) (Lightning lmpulse Voltage test, Chopped impulse voltage test, Multi chopped irnpulse voltage test)	160000.0
10.1.2(b) (Lightning lmpulse Voltage test, Chopped impulse voltage test, Multi chopped irnpulse voltage test)	175000.0
10.1.2(b) (Lightning lmpulse Voltage test, Chopped impulse voltage test, Multi chopped irnpulse voltage test)	250000.0
10.1.2(b) (Lightning lmpulse Voltage test, Chopped impulse voltage test, Multi chopped irnpulse voltage test)	300000.0
10.1.2(b) (Lightning lmpulse Voltage test, Chopped impulse voltage test, Multi chopped irnpulse voltage test)	400000.0
10.1.2(b) (Lightning lmpulse Voltage test, Chopped impulse voltage test, Multi chopped irnpulse voltage test)	500000.0
10.1.2(b) (Lightning lmpulse Voltage test, Chopped impulse voltage test, Multi chopped irnpulse voltage test)	125000.0
10.1.2(b) (Lightning lmpulse Voltage test, Chopped impulse voltage test, Multi chopped irnpulse voltage test)	140000.0
10.1.2(b) (Lightning lmpulse Voltage test, Chopped impulse voltage test, Multi chopped irnpulse voltage test)	200000.0
10.1.2(b) (Lightning lmpulse Voltage test, Chopped impulse voltage test, Multi chopped irnpulse voltage test)	250000.0
10.1.2(b) (Lightning lmpulse Voltage test, Chopped impulse voltage test, Multi chopped irnpulse voltage test)	260000.0
10.1.2(b) (Lightning lmpulse Voltage test, Chopped impulse voltage test, Multi chopped irnpulse voltage test)	285000.0
10.1.2(b) (Lightning lmpulse Voltage test, Chopped impulse voltage test, Multi chopped irnpulse voltage test)	400000.0
10.1.2(b) (Lightning lmpulse Voltage test, Chopped impulse voltage test, Multi chopped irnpulse voltage test)	500000.0
10.1.2(b) (Lightning lmpulse Voltage test, Chopped impulse voltage test, Multi chopped irnpulse voltage test)	600000.0
10.1.2(b) (Lightning lmpulse Voltage test, Chopped impulse voltage test, Multi chopped irnpulse voltage test)	800000.0
10.1.3(g) (Measurement of Hormonices of the no load current)	10000.0
10.1.3(j) (Measurement of Insulation Resistance)	2400.0
10.1.1(b) (Measurement of Voltage ratio & voltage vec,tor group test)	3200.0
10.1.1(a) (Windlng Resistance)	1600.0
10.1.3(d) (Measurement of Zero phase sequence impedance for 3 Phase transformer)	3000.0
10.1.1(e) (AC voltage withstand test)	4000.0
10.1.1(e) (Induced Overvoltage)	6400.0
10.1.1(d) (No Load loss and current)	9600.0
10.1.1 (C) (% impedance and load loss)	12800.0
10.1.2(a) (Temperatur Rise)	20000.0
10.1.3 (f) (Noise Level)	10000.0
7 (As per Specification)	-
7 (Rating Plate Details)	-
17.3.2 (b) of CBIP Pub. No. 317 (Oil Leakage Test (Pressure Test - Type))	10000.0
17.3.1 (a) of CBIP Pub. No. 317 (Pressure Test Routine (Deflection))	8000.0
17.3.2 (a) of CBIP Pub. No. 317 (Vacuum Test - Type (Deflection))	10000.0
As per CBIP No. 317 Cl. 3.10 (Magnetic Balance Test)	3000.0
As per IS : 335 (Breakdown Voltage Test)	10000.0
CBIP Publication no. 317 (Polarization Index Test)	2500.0
CBIP Publication no. 317 (Measurement of Unbalance Current)	5000.0
CBIP Publication no. 317 (Measurement of Unbalance Current)	5000.0
17.3.2 (a) of CBIP Pub. No. 317 (Vacuum Test - Type (Deflection))	10000.0
As per CBIP No. 317 Cl. 3.10 (Magnetic Balance Test)	3000.0
As per IS : 335 (Breakdown Voltage Test)	10000.0
CBIP Publication no. 317 (Polarization Index Test)	2500.0
CBIP Publication no. 317 (Measurement of Unbalance Current)	5000.0
CBIP Publication no. 317 (Measurement of Unbalance Current)	5000.0
CBIP (Measurement of Unbalance Current)	3000.0
10.1.1(a) (Measurement of windlng Resistance)	1600.0
10.1.1(e) (Separate source AC voltage withstand test)	4000.0
10.1.3(g) (% Harmonics)	10000.0
10.1.3(j) (Measurement of Insulation Resistance)	2400.0
10.1.1(b) (Voltage ratio & Phase Displacement)	3200.0
10.1.1(a) (Windlng Resistance)	1600.0
10.1.3(d) (Zero Sequence Impedance)	3000.0
10.1.1(e) (Separate source AC voltage withstand test)	4000.0
10.1.2(b) (Lightning lmpulse Voltage test / Chopped Lightning Impulse Voltage Test (Power Transformer upto 10 MVA))	250000.0
10.1.2(b) (Lightning lmpulse Voltage test, Chopped impulse voltage test, Multi chopped irnpulse voltage test)	85000.0
10.1.2(b) (Lightning lmpulse Voltage test, Chopped impulse voltage test, Multi chopped irnpulse voltage test)	130000.0
10.1.2(b) (Lightning lmpulse Voltage test, Chopped impulse voltage test, Multi chopped irnpulse voltage test)	140000.0
10.1.2(b) (Lightning lmpulse Voltage test, Chopped impulse voltage test, Multi chopped irnpulse voltage test)	160000.0
10.1.2(b) (Lightning lmpulse Voltage test, Chopped impulse voltage test, Multi chopped irnpulse voltage test)	175000.0
10.1.2(b) (Lightning lmpulse Voltage test, Chopped impulse voltage test, Multi chopped irnpulse voltage test)	250000.0
10.1.2(b) (Lightning lmpulse Voltage test, Chopped impulse voltage test, Multi chopped irnpulse voltage test)	300000.0
10.1.2(b) (Lightning lmpulse Voltage test, Chopped impulse voltage test, Multi chopped irnpulse voltage test)	400000.0
10.1.2(b) (Lightning lmpulse Voltage test, Chopped impulse voltage test, Multi chopped irnpulse voltage test)	500000.0
10.1.2(b) (Lightning lmpulse Voltage test, Chopped impulse voltage test, Multi chopped irnpulse voltage test)	125000.0
10.1.2(b) (Lightning lmpulse Voltage test, Chopped impulse voltage test, Multi chopped irnpulse voltage test)	140000.0
10.1.2(b) (Lightning lmpulse Voltage test, Chopped impulse voltage test, Multi chopped irnpulse voltage test)	200000.0
10.1.2(b) (Lightning lmpulse Voltage test, Chopped impulse voltage test, Multi chopped irnpulse voltage test)	250000.0
10.1.2(b) (Lightning lmpulse Voltage test, Chopped impulse voltage test, Multi chopped irnpulse voltage test)	260000.0
10.1.2(b) (Lightning lmpulse Voltage test, Chopped impulse voltage test, Multi chopped irnpulse voltage test)	285000.0
10.1.2(b) (Lightning lmpulse Voltage test, Chopped impulse voltage test, Multi chopped irnpulse voltage test)	400000.0
10.1.2(b) (Lightning lmpulse Voltage test, Chopped impulse voltage test)	500000.0
10.1.2(b) (Lightning lmpulse Voltage test, Chopped impulse voltage test)	600000.0
10.1.2(b) (Lightning lmpulse Voltage test, Chopped Impulse Voltage Test)	800000.0

IS 1180 : Part 1 (2014) - Outdoor Type Oil Immersed Distribution Transformers - Specification Part 1 Mineral Oil Immersed (Fourth Revision) (1100 kVA to 2 500 kVA) [1100 kVA to 2 500 kVA]

Outdoor Type Oil Immersed Distribution Transformers - Specification Part 1 Mineral Oil Immersed (Fourth Revision) (1100 kVA to 2 500 kVA)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
21.5.1.121.5.2.121.5.3.1 (Vacuum Pressure (Type Test))	20000.0
21.3(b) (Temperatur Rise Test)	40000.0
21.2(g) (Separate Source AC voltage withstand test)	2500.0
21.5.1.221.5.2.221.5.3.2 (Pressure test (routine))	5000.0
21.4.(d) (Adhesion by Tape Test)	5000.0
21.5.1.321.5.2.321.5.3.3 (Oil leakage test)	7000.0
21.2(a) (Measurement of Winding Resistance)	1000.0
21.2(b) (Measurement of voltage ratio and,check ofvoltage vector relationship)	2000.0
7.9 & 8.9 (Measurement of Permissible flux density and over fluxing)	20000.0
21.4( c) (Measurement of No load current at 112.5 percent voltage)	2000.0
21.2(e) (Measurement of insulation resistance)	1500.0
21.2(c) (Measurement of impedance voltage (principal tapping), shortcurcuit impedance and load loss (At 50% and 100% load))	8000.0
21.2(d) (Measurement of no Load and loss and current)	6000.0
21.2(f) (lnduced Over Voltage withstand test)	4000.0
21.4(a) (Determination of sound levels)	7000.0
21.4( e) (BDV of Oil in the tranformer)	10000.0
21.5.1.121.5.2.121.5.3.1 (Air Pressure (Type test)-Deflection)	20000.0
21.3(a) (Impulse Voltage)	35000.0
21.3(a) (lmpulse Voltage)	65000.0
21.3(a) (lmpulse Voltage)	50000.0
21.3(a) (lmpulse Voltage)	40000.0
21.3(a) (lmpulse Voltage)	35000.0
21.3(a) (lmpulse Voltage)	65000.0
21.5.2.1 (Permanent Deflection)	20000.0
21.4( e) (Break Down Voltage)	10000.0
21.4(a) (Sound Levels)	7000.0
21.4(a) (Sound Levels)	6000.0
21.4(a) (Sound levels)	5000.0
21.4(a) (Sound Level)	5000.0
21.2(f) (lnduced Over Voltage withstand test)	4000.0
21.2(f) (lnduced Over Voltage withstand test)	3000.0
21.2(f) (lnduced Over Voltage withstand test)	2500.0
21.2(f) (lnduced Over Voltage withstand test)	1200.0
21.2(d) (No Load loss and current)	6000.0
21.2(d) (No Load loss and current)	6000.0
21.2(d) (No Load loss and current)	3000.0
21.2(c) (Load Loss and % Impedance)	8000.0
21.2(c) (Load Loss and % Impedance)	7000.0
21.2(c) (Load Loss and % Impedance)	6000.0
21.2(c) (Load Loss and % Impedance)	5000.0
21.2(c) (Load Loss and % Impedance)	3000.0
21.2(e) (Insulation Resistance)	1500.0
21.2(e) (Insulation Resistance)	1500.0
21.2(e) (insulation resistance)	1500.0
21.4( c) (No load current)	2000.0
8.9 (flux density and over fluxing)	20000.0
8.9 (flux density and over fluxing)	15000.0
7.9 (flux density and over fluxing)	10000.0
6.9 (flux density and over fluxing)	6500.0
21.2(b) (voltage ratio and voltage vector relationship)	2000.0
21.2(b) (voltage ratio and voltage vector relationship)	1500.0
21.2(b) (voltage ratio)	700.0
21.2(a) (Winding Resistance)	1000.0
21.2(a) (Winding Resistance)	700.0
21.5.3.3 (Oil leakage test)	5000.0
21.5.2.3 (Oil leakage test)	7000.0
21.5.1.3 (Oil Leakage Test)	7000.0
21.5.3.2 (Oil Leakage Test)	3500.0
21.5.2.2 (Oil Leakage Test)	5000.0
21.5.1.2 (Oil Leakage Test)	5000.0
21.2(g) (AC High Voltage Withstand Test)	2500.0
21.2(g) (AC High Voltage Withstand test)	1200.0
21.3(b) (Temperature Rise of Oil and Windings.)	40000.0
21.3(b) (Temperature Rise of the Oil and Windings.)	35000.0
21.3(b) (Temperature Rise of Oil and Windings.)	30000.0
21.3(b) (Temperatur Rise of Oil and Windings.)	15000.0
21.5.3.1 (Permanent Deflection)	6000.0
21.5.2.1 (Permanent Deflection)	15000.0
21.5.1.1 (Permanent Deflection)	10000.0
As per CBIP Pub No. 317 Cl. 3.17 (Magnetic Balance Test)	5000.0
As per CBIP Manual No. 317 Cl. (Harmonics of No-load Current)	15000.0
As per CBIP No. 317 Cl. 3.10 (Zero Sequence Impedance Measurement)	5000.0
As per CBIP No. 317 Cl. 3.10 (Magnetic Balance Test)	5000.0
N.A. (Unbalance Current)	5000.0
CBIP Publication no. 317 (Polarization Index)	2500.0

IS 650:1991 - Standard sand for testing cement

Standard sand for testing cement

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4.1 (Colour)	500.0
4.1 (Silt (CPWD Specification -Vol I))	1000.0
4.1 (Shape (IS 383:2016))	1000.0
4.2 (Size-Sieve analysis -Particle size distribution)	2000.0
custom (Specific gravity-IS 2386(Part III))	500.0
Custom (Water absorption-IS 2386(Part III))	1000.0
5.1 (Organic Impurities)	1000.0
5.1 (The loss of mass -on extraction with hot HCl)	1200.0
custom (Chemical properties: CaO,SiO2,Al2O3,Fe2O3,Loss on Ignition(as per IS 4032))	4000.0
custom (Compressive strength (IS 4031/IS 456))	3000.0

CUSTOM/SR/CHEMICAL (2024) - Customized Specification for Chemical analysis

Customized Specification for Chemical analysis

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Custom (Test Results of Chemical composition (in Annexure))	5000.0
Custom (Test Results of Soil sample in Annexure (NON-NABL))	6000.0

IS 3951(2):2023 - Hollow clay tiles for floors and roofs-structural type

Hollow clay tiles for floors and roofs-structural type

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4 (General requirements)	1000.0
5 (Dimensions and Tolerances)	1000.0
6 (Bulk density)	1000.0
7 (Compressive strength)	2000.0
8 (Water absorption)	1000.0

IS 3951(1):2023 - Hollow Clay Tiles for Floors and Roofs — (Part 1) Filler Type

Hollow Clay Tiles for Floors and Roofs — (Part 1) Filler Type

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4 (General requirements)	1000.0
5 (Dimensions and Tolerances)	1000.0
6 (Bulk density)	1000.0
7 (Breaking strength)	2000.0
8 (Water absorption)	1000.0

CUS/SR/MECH-55 (2024) - Mechanical Properties of Metal

Mechanical Properties of Metal

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1.0 (Dimensions, mm)	2000.0
2.0 (Brinell Hardness, HBW)	2000.0
3.0 (Chemical composition, % by mass)	5000.0
4.0 (Mass of Zinc Coating, g/m²)	2000.0
5.0 (Powder Coating Thickness, micron)	2000.0
6.0 (Tensile strength, N/mm²)	1000.0
7.0 (Yield strength, N/mm²)	1000.0
8.0 (Percentage Elongation, %)	1000.0
9.0 (Weight, kg)	1000.0
10.0 (Tensile Load, kN)	3000.0
11.0 (Yield Load, kN)	3000.0
3.1 (Copper Purity, %)	2400.0
12 (Capacity, ml)	1000.0

251 (2024) - SODA ASH, TECHNICAL

SODA ASH, TECHNICAL

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4.1 (Description)	1200.0
4.2 (Bulk Density)	1200.0
4.3 (Volatile Matter Content)	1200.0
4.4 (Sieve Analysis of Dense Grade Soda Ash)	1200.0
4.5 (Total alkalinity (as Na2CO3))	1200.0
4.5 (Matter insoluble in water)	1200.0
4.5 (Sulphate (Na2SO4))	1200.0
4.5 (Chloride (as NaCl))	1200.0
4.5 (Iron (as Fe2O3))	1200.0

13620 (1993) - FUSION BONDED EPOXY COATED REINFORCING BARS-SPECIFICATION

FUSION BONDED EPOXY COATED REINFORCING BARS-SPECIFICATION

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
8.3 (Adhesion of Coating (Bend Test))	1000.0
5 (Surface Preparation (Visual Examination))	1000.0

IS 1626 : Part 3 (1994) - Asbestos Cement Building types and Pipe Fittings, Gutters and Gutter Fittings and Roofing Fittings - Part 3 : Roofing Fittings

Asbestos Cement Building types and Pipe Fittings, Gutters and Gutter Fittings and Roofing Fittings - Part 3 : Roofing Fittings

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6 (Impermeability test)	1500.0
5 (Dimensions & Visual examination)	5000.0
7 (General appearance & Finish)	1000.0

IS 2721 (2003) - Galvanized Steel Chain Link Fence Fabric

Galvanized Steel Chain Link Fence Fabric

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6.2 (Mesh Size)	500.0
6.3 (Width)	500.0
6.3 (Length)	500.0
6.1 (Nominal Dia of Mesh Wire)	500.0
6.1 (Diameter of Line wire)	500.0
9.1.1 (Tensile strength of Mesh wire)	1500.0
9.1.1 (Tensile strength of Line wire)	1500.0
9.1.2 (Wrapping Test of Mesh Wire)	1000.0
9.1.2 (Wrapping test of Line wire)	1000.0
9.1.3 (Twist Test of Mesh Wire)	2000.0
9.1.3 (Twist Test of Line Wire)	2000.0
9.1.4 (Bend test of Mesh wire)	500.0
9.1.4 (Bend Test of Line wire)	500.0
9.2 (Mass of Zinc Coating of Mesh Wire)	2000.0
9.2 (Mass of Zinc Coating of Line Wire)	2000.0

IS 15961 (2012) - Hot Dip Aluminium-Zinc Alloy Metallic Coated Steel Strip and Sheet (Plain)

Hot Dip Aluminium-Zinc Alloy Metallic Coated Steel Strip and Sheet (Plain)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
9.1 (Mass of coating (Both sides), g/Sq m)	2000.0
8.3 (Tensile Strength)	1000.0
8.3 (Yield Strength)	1000.0
8.3 (Percent Elongation)	1000.0
7.1 (Carbon. percent)	500.0
7.1 (Manganese, percent)	500.0
7.1 (Sulphur, percent)	500.0
7.1 (Phosphorous, percent)	500.0
7.1 (Aluminium, Percent)	500.0
7.1 (Silicon, Percent)	500.0
3.2 (Thickness of Sheet (base metal thickness), mm)	1000.0
3.3 (Coated thickness (total coated thickness), mm)	1000.0

IS 13238 (2021) - Epoxy Based Zinc Phosphate Primer (Two Pack ) — Specification

Epoxy Based Zinc Phosphate Primer (Two Pack ) — Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Epoxy Based Zinc Phosphate Primer (Two Pack) — Specification (Please refer annexure for tests result)	23000.0

6047 (2009) - Scouring products for utensil cleaning - Specification

Scouring products for utensil cleaning - Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4.2 (Retention on 250-micron IS Sieve)	1200.0
4.2 (Active matter)	1200.0
4.2 (Active (Reserve) alkalinity)	1200.0
4.2 (Matter insoluble in alcohol)	1200.0
4.2 (Moisture and volatile matter content at 105°C)	2400.0
4.2 (Lather)	1200.0
4.2 (Cleaning efficacy, number of plates cleaned per 5g of sample)	1200.0
4.2 (Tough soil cleaning)	1200.0
4.2 (Surface damage)	1200.0

ASME B 29.1 (2011) - Precision Power Transmission Roller Chain

Precision Power Transmission Roller Chain

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
3.3 (Dimensions, mm)	2000.0
3.3 (Chain length, mm)	1000.0
3.4.2 (Breaking load, kN)	4000.0

First
Prev
1
2
3
4
Next
Last