NTH - Management Information System

National Test House (WR), Mumbai

Plot No. F 10, M.I.D.C, Marol, Andheri (E), Mumbai Maharashtra - 400093, Mumbai, Mumbai, Maharashtra, 400093

28260927 director-mum[at]nth[dot]gov[dot]in

Scope List

Reset

659 Results

S.No.

Standard No.

Product

Testing Charges (Excl. Of Taxes)

301

IS 13213 (2018) - Polyurethane Full Gloss Enamel (Two Pack) — Specification

Polyurethane Full Gloss Enamel (Two Pack) — Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Polyurethane Full Gloss Enamel (Two Pack) — Specification (Please refer annexure for tests result)	46000.0

302

IS 13238 (2021) - Epoxy Based Zinc Phosphate Primer (Two Pack ) — Specification

Epoxy Based Zinc Phosphate Primer (Two Pack ) — Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Epoxy Based Zinc Phosphate Primer (Two Pack) — Specification (Please refer annexure for tests result)	23000.0

303

IS 13183 (1991) - ALUMINIUM PAINT, HEAT RESISTANT SPECIFICATION

ALUMINIUM PAINT, HEAT RESISTANT SPECIFICATION

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
ALUMINIUM PAINT, HEAT RESISTANT — SPECIFICATION (Please refer annexure for tests result)	8000.0

304

TEC/GR/FA/CDS-008/AUG-19 - Permanently lubricated HDPE Telecom Duct

Permanently lubricated HDPE Telecom Duct

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Tensile Strength(N/sq.mm.) as per ASTM D 638)	2000.0
- (Elongation(%) as per ASTM D 638)	2000.0
- (Longitudinal reversion test(%)as per IS 4984)	2000.0
- (Impact Strength as per IS 12235(Part 9))	2000.0
- (Crush resistance)	3000.0

305

IRC SP 80-2008 (2008) - Guidelines for Corrosion Prevention

Guidelines for Corrosion Prevention

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Guidelines for corrosion prevention (Specific Gravity)	1200.0
Guidelines for corrosion prevention (Solid Contents)	1500.0
Guidelines for corrosion prevention (IR Spectrum (FTIR))	2000.0
Guidelines for corrosion prevention (Adhesion with concrete (ASTM D 4541))	10000.0
Guidelines for corrosion prevention (Dry Film Thickness (for minimum 2 coats))	1200.0
Guidelines for corrosion prevention (Coverage (2 coats))	1200.0
Guidelines for corrosion prevention (Water proofing characteristics (DIN 1048/ISO 12290))	10000.0
Guidelines for corrosion prevention (Re-coatability)	1200.0
Guidelines for corrosion prevention (Water Vapour Transmission (ASTM D 1653))	5000.0
Guidelines for corrosion prevention ((%) Elongation (ASTM D 2370))	2000.0
Guidelines for corrosion prevention (Tensile strength (ASTM D 2370))	2000.0
IRC SP 80 (UV Accelerated Weathering Test (ASTM G 53) 400 hrs)	24000.0

306

IS 15769 (2008) - Flux Cored (Tubular) Electrodes for Gas Shielded and Self Shielded Metal welding of Carbon or Carbon Manganese Steel

Flux Cored (Tubular) Electrodes for Gas Shielded and Self Shielded Metal welding of Carbon or Carbon Manganese Steel

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4.1 (Diameter of Core Wire)	500.0
4.2 (Temper)	1000.0
4.2 (Cast)	500.0
4.2 (Helix)	500.0
4.3 (Uniformity)	500.0
4.4.2 (Coils with Former, Overall Diameter, A)	500.0
4.4.2 (Coils with Former, Width, B)	500.0
4.4.2 (Coils with Former, Inner Diameter, C)	500.0
4.4.2 (Coils with Former, Inner Diameter, C, Max)	500.0
4.4.3 (Spools, Overall Diameter A)	500.0
4.4.3 (Spools, Overall Width, B)	500.0
4.4.3 (Spools, Inner Diameter, C)	500.0
4.4.3 (Spools, Distance Between Axes D)	500.0
4.4.3 (Spools, Driving Hole Diameter E)	500.0
4.4.3 (Spools, Weight, Max)	500.0
5.8 (Chemical Analysis)	5000.0
5.2 (Radiographic Examination)	1500.0
5.3 (Tensile Test)	3000.0
5.4 (Charpy Impact Test)	3000.0
5.1.3.2 (Dimension of Fillet Weld)	500.0
5.1.3.2 (Fillet Weld Fracture)	4000.0
5.5 (Transverse Tensile Test)	3000.0
5.6 (Longitudinal Guided Bend Test)	1000.0
5.7 (Diffusible Hydrogen Test)	5000.0

307

Customized Specification for Struct Guard Carbon Sheet - Customized Specification for Struct Guard Carbon Sheet

Customized Specification for Struct Guard Carbon Sheet

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Tensile Strength(N/sq.mm.) as per ASTM D 3039)	2000.0
- (Tensile Modulus(N/sq.mm) as per ASTM D 3039)	2000.0
- (Elongation(%) as per ASTM D 3039)	2000.0

308

NTH/WR/ME(CAL)/SOP/07 - Calibration of Measuring Tape

Calibration of Measuring Tape

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Linear Measurment of Measuring Tape (up to 1 meter))	1200.0
2 (Linear Measurment of Measuring Tape (up to 3 meter))	2000.0
3 (Linear Measurment of Measuring Tape (up to 5 meter))	2500.0
4 (Linear Measurment of Measuring Tape (up to 15 meter))	3500.0
5 (Linear Measurment of Measuring Tape (up to 50 meter))	5000.0

309

NTH/WR/ME(CAL)/SOP/06 (2023) - Calibration of Measuring Steel Scale (0-1000mm)

Calibration of Measuring Steel Scale (0-1000mm)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Linear Measurment of Steel Scale (0-300mm))	1200.0
2 (Linear Measurment of Steel Scale (0-600mm))	1200.0
3 (Linear Measurment of Steel Scale (0-1000mm))	1200.0

310

NTH/WR/ME(CAL)/SOP/05 (2023) - Calibration of Direct Pressure Indicating Device

Calibration of Direct Pressure Indicating Device

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Calibration of Direct Pressure Indicating device/Master Pressure Gauge (Range 1 to 690) bar by Comparison Method)	3000.0

311

NTH/WR/ME(CAL)/SOP/04 (2023) - Verification of UTM/Tension/Compression Testing Machine

Verification of UTM/Tension/Compression Testing Machine

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Calibration of UTM in Tension Mode up to 50kN (1 Scale))	6000.0
2 (Calibration of UTM in Compression Mode up to 500kN (1 Scale))	7000.0

312

NTH/WR/ME(CAL)/SOP/01 (2023) - Calibration of External Micrometer

Calibration of External Micrometer

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Calibration of External Micrometer (up to 25mm))	1200.0

313

NTH/WR/ME(CAL)/SOP /03 (2023) - Calibration of Test Sieves for Wire Cloth Test Sieves and Perforated Plate Test Sieves

Calibration of Test Sieves for Wire Cloth Test Sieves and Perforated Plate Test Sieves

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Test Sieves ( Aperture Size By Comparison Method - Tool Maker Microscope))	2000.0
2 (Test Sieves ( Aperture Size By Comparison Method - Vernier Caliper))	2000.0

314

NTH/WR/ME(CAL)/SOP /02 (2023) - Calibration of Vernier Caliper/Digital Caliper

Calibration of Vernier Caliper/Digital Caliper

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Dimension - Length ( Range 0-300mm))	1200.0
2 (Dimension - Length ( Range 0-600mm))	2000.0
3 (Dimension-Length ( Range 0-1000mm))	2000.0

315

IS 16491 : Part 1 (2024) - Geometrical product specifications (GPS) - Dimensional measuring equipment: Part 1 calipers; design and metrological characteristics

Geometrical product specifications (GPS) - Dimensional measuring equipment: Part 1 calipers; design and metrological characteristics

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5 (Length)	1200.0
5 (Length)	2000.0
5 (Length)	2000.0
5 (Length)	2000.0

316

IS 460 : Part 2 (2020) - Test Sieves — Specification Part 2 Perforated Plate Test Sieves ( Fourth Revision )

Test Sieves — Specification Part 2 Perforated Plate Test Sieves ( Fourth Revision )

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5 (Aperture Size)	2000.0

317

IS 460 : Part 1 (2020) - Test Sieves — Specification Part 1 Wire Cloth Test Sieves ( Fourth Revision )

Test Sieves — Specification Part 1 Wire Cloth Test Sieves ( Fourth Revision )

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5 (Aperture size)	2000.0

318

IS 15388 (2003) - Specification for Silica Fume

Specification for Silica Fume

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4 (Alkalies as Na2O)	1200.0
4 (Loss in Ignition)	1200.0
4 (Moisture)	1200.0
4 (Silica)	1200.0
5 [Table 2 (ii)] (Oversize percent retained on 45 micron IS sieve,)	1000.0
5 [Table 2 (iv)] (Compressive Strength at 7 days as percent of control sample,)	3000.0

319

17048 (2018) - Halogen Free Flame Retardant (HFFR) Cables for Working Voltages up to and including 1100 Volts - Specification

Halogen Free Flame Retardant (HFFR) Cables for Working Voltages up to and including 1100 Volts - Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Table 2 II (Acceptance tests)	12000.0
Table 2 II (c) (Persulphate test)	1500.0
Table 2 II (k) (pH and Conductivity)	1500.0
Table 2 III (Type tests)	35000.0

320

Kota Stone (PCE Cir No. 22/2007/Works - ECRly - Specification for Kota Stone Flooring

Specification for Kota Stone Flooring

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
2.3.1 (Abrasion Resistance (Resistance to wear - on lines of 1706))	2000.0
2.3.1 (Modulus of Rupture in wet condition (on lines of IS 1121))	2000.0
2.3.1 (Compressive Strength (on lines of IS 1121 - 1), In wet condition)	2000.0
2.3.1 (Hardness (Moh's Scale- on the lines of IS 13630))	2000.0
3.3 (Water Absorption (on the lines of IS 1124), %)	1000.0
2.3.1 (Specific Gravity (on the lines of IS 1122))	1000.0
2.3.1 (Water Absorption (on lines of IS 1237: 2012), %)	1000.0
2.2 (Size and Thickness & Tolerances, mm)	2000.0

321

IEC 61238-1-1 (2019) - Test methods and requirements for compression and mechanical connectors for power cables for rated voltages up to 1kV (Um=1.2kV) tested on non-insulated conductors

Test methods and requirements for compression and mechanical connectors for power cables for rated voltages up to 1kV (Um=1.2kV) tested on non-insulated conductors

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6 (Electrical tests)	65000.0
7 (Mechanical strength for the connectors to the conductors of power cables)	5000.0
BS:1977 (Chemical Composition)	5000.0

322

IS 319 (2007) - Free cutting brass bars, rods and section - Specification (Fifth Revision)

Free cutting brass bars, rods and section - Specification (Fifth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
9.1 (Tensile Strength)	2000.0
9.1 (Elongation)	1000.0
9.2 (Vickers Hardness)	2000.0
7 (Dimensions)	1000.0
5 (Freedom from defects)	1000.0
Cl. 8.1 Table-1 (Grade-I or Grade-II) NABL (Cl. 8.1 Table -1 (Grade-I or Grade-II) (Pl. see Annexure)-NABL)	6000.0
Cl.no8.1,Table 1 (Chemical Composition( Please see the Annexure) NON NABL)	1.0

323

IS 2645:2003 (RA 2017) - Integral Waterproofing Compounds for Cement Mortar and Concrete-Specification

Integral Waterproofing Compounds for Cement Mortar and Concrete-Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
3.2.a. (Setting time -Initial)	500.0
3.2.b (Setting time-Final)	500.0
3.1 (Permeability to water(IS 2645:2003 Annex B))	3000.0
3.3.a (Compressive strength-3 days)	2000.0
3.3.b (Compressive strength-7 days)	2000.0
3.4 (Chloride content)	2000.0
- (Test for Heavy Metals by AAS method.)	2000.0
Toxic Elements (Toxic Elements (By AAS method))	3000.0
- - (VOC matter)	3000.0
- (pH)	1000.0

324

Custom Specification for General Chemical -1 - Custom Specification for General Chemical-1

Custom Specification for General Chemical-1

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Annexure (Results as per Annexure)	10000.0

325

Customized specification on the lines of ASTM D 430 - Standard Test Method For Rubber Deterioration-Dynamic Fatigue

Standard Test Method For Rubber Deterioration-Dynamic Fatigue

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Resistance to cracking(Number of cycles required for the first sign of crack))	5000.0

326

Customer specification - Flame retardant test for 4 hours

Flame retardant test for 4 hours

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
27600 (FLAME RETARDANT TEST FOR 4 Hrs.)	3000.0

327

ASTM D2240 (2015) - Standard Test Method for Rubber Property—Durometer Hardness

Standard Test Method for Rubber Property—Durometer Hardness

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found

328

Custom CC Tiles, NTH(WR) - Cement Based Tiles - Terrazo

Cement Based Tiles - Terrazo

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7 & 8.1 of IS 1237 (Dimension & Tolerances (On the lines of IS 1237), in mm)	500.0
7 & 8.1 of IS 1237 (Thickness and Thickness of wearing layer (on the lines of IS 1237), in mm)	500.0
12.2 of IS 1237 (Flatness of tiles (on lines of IS 1237 cl. 12.2), in %)	500.0
12.3 of IS 1237 (Perpendicularity of tiles (on lines of IS 1237 cl. 12.3), in %)	500.0
12.4 of IS 1237 (Straightness of tiles (on lines of IS 1237 cl. 12.4), in %)	500.0
12.5 of IS 1237 (Water Absorption (On lines of IS 1237 Cl. 12.5), in %)	1000.0
12.6 of IS 1237 (Wet Transverse Strength (On lines of IS 1237 Cl. 12.6), in %)	2000.0
12.7 of IS 1237 (Resistance to Wear (on the lines of IS 1237 Cl 12.7), in mm)	2000.0
Part 13 - IS 13630 (Scratch Hardness on Mho's Scale (One the lines of IS 13630 (Part 13)))	2000.0
Part 14 - IS 13630 (Drop Ball Impact Resistance (on lines of IS 13630 (Part 14)))	2000.0
6.1 of IS 3367 (Compressive Strength (on the lines of IS 3367), MPa)	2000.0
Part 4 of IS 13630 (Coefficient of Linear Thermal Expension (on the lines of IS 13630 -Part 4),)	3000.0
IS 101 (Gloss at 60 Deg. (on the lines of IS 101))	1200.0

329

IS 636 (2018) - Non-percolating flexible fire fighting delivery hose

Non-percolating flexible fire fighting delivery hose

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6.1 (General Requirements-Inner Lining)	1500.0
6.2 (Internal Diameter, mm)	1000.0
6.3 (Length, m)	1000.0
6.4 (Mass, g)	1000.0
6.5 (Coil Diameter, cm)	1000.0
6.6 (Hydrostatic Proof Pressure Test)	5000.0
6.7 (Hydrostatic Burst Pressure Test)	5000.0
6.8 (Kink Test)	2000.0
6.9 (Change in Length, %)	1000.0
6.10 (Change in Diameter, %)	1000.0
6.11.1 (Adhesion, mm/minute)	2000.0
6.11.2 (Accelerated Ageing- Appearance)	1000.0
6.11.2 (Accelerated Ageing- Hydrostatic Burst Pressure Test)	5000.0
6.11.2 (Accelerated Ageing- Adhesion, mm/minute)	2000.0
6.12 (Abrasion Resistance)	2000.0
6.13 (Water Pick Up / Moisture Absorption, kg/Sq. m.)	1000.0
6.14 (Heat Resistance)	2000.0
6.15 (Oil Resistance Test- Appearance)	1000.0
6.15 (Oil Resistance Test - Adhesion)	2000.0

330

MICR Cheque Paper Sensitization to chemicals and UV Light - MICR Cheque Paper Sensitization to chemicals and UV Light

MICR Cheque Paper Sensitization to chemicals and UV Light

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Test for Chemical Sensitization Ethanol)	450.0
2 (Test for Chemical Sensitization Acetone)	450.0
3 (Test for Chemical Sensitization Benzene)	450.0
4 (Test for Chemical Sensitization Chloroform)	450.0
5 (Test for Chemical Sensitization Ethylene Glycol")	450.0
6 (Test for Chemical Sensitization Bleaching powder)	450.0
7 (Test for Chemical Sensitization Ammonia solution 30%)	450.0
8 (Test for Chemical Sensitization Sodium meta bisulfite solution 10%)	450.0
9 (Test for Chemical Sensitization Oxalic acid solution 5%)	450.0
10 (Test for Exposure to UV lamp (for 24 Hours))	350.0
11 (GSM)	100.0