NTH - Management Information System

National Test House (WR), Mumbai

Plot No. F 10, M.I.D.C, Marol, Andheri (E), Mumbai Maharashtra - 400093, Mumbai, Mumbai, Maharashtra, 400093

28260927 director-mum[at]nth[dot]gov[dot]in

Scope List

Reset

659 Results

S.No.

Standard No.

Product

Testing Charges (Excl. Of Taxes)

511

IS / ASTM / DIN / EN / BS - Construction Chemicals used for water proofing / Admixtures

Construction Chemicals used for water proofing / Admixtures

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
IS 9103, Cl. 9 (Aspect (as per IS 9103:1999, Cl. 9))	1000.0
IS 9103, Cl. 9 (Colour (as per IS 9103:1999, Cl. 9))	1000.0
IS 9103, Cl. 9 (pH Value (IS 9103:1999, Cl. 9))	1000.0
IS 3104 (Part 2) (Specific Gravity (IS 3104 (Part II)))	1000.0
IS 101 (Viscosity (IS 101))	1000.0
ASTM D 7234-12 (Pull-off Adhesion Strength of coating (ASTM D 7234-2012),)	5000.0
ASTM D 7234-12 (Pull-off Adhesion Strength of coating (ASTM D 7234-2012), a) Control Sample b) Coated Sample)	10000.0
IS 4031 (Transverse Strength (Flexural Strength) at 28 days (IS 4031 (Part 8)).)	4000.0
DIN (Water Permeability (DIN 1048))	10000.0
IS 9103, Cl. 9 (Dry Material (IS 9103:1999, Cl 9))	1000.0
IS 9103, Cl. 9 (Chloride Content (IS 9103:1999))	1000.0
IS 9103, Cl. 9 (Relative Density (IS 9103:1999))	1000.0
Cl 7.2.1, IS 9103:1999 (Slump Test (Workability),)	2000.0
Cl 8.2.1, IS 9103:1999 (Compressive Strength, Comparative Compressive Strength (IS 9103:1999), at 7 days)	5000.0
Cl 8.2.1, IS 9103:1999 (Compressive Strength, Comparative Compressive Strength (IS 9103:1999), at 28 days)	5000.0
EN 12390 / DIN 1048 (Water Permeability of Concrete, Comparative (EN 12390), at 28 days)	10000.0
Cl 8.2.3, IS 9103:1999 (Length Change, Percent increase over Control Sample), (IS 9103:1999))	2000.0
BS 1881- Part 122:1983 (Water Absorption (BS 1881 (Part 122):1983)	2000.0
ASTM D 412 (Tensile Strength (ASTM D 412), N/mm^2)	2000.0
ASTM D 412 (Elongation at Break (ASTM D 412), %)	2000.0
ASTM D 4541 (Pull-off Adhesion Strength of coating (ASTM D 4541-2009),)	5000.0
ASTM D 2370 (Tensile strength and Elongation at break (on the lines of ASTM D 2370))	4000.0
ASTM C 1059 / 1042 (Bond Strength of Latex (Slant Shear Strength on lines of ASTM C 1042), in N/mm^2)	5000.0
ASTM C 882 (Bond Strength (Slant Shear Strength - on lines of ASTM C 882) after 28 days, in N/mm^2)	5000.0
ASTM C 882 (Bond Strength (Slant Shear Strength - on lines of ASTM C 882) after 14 days, in N/mm^2)	5000.0
EN 196-1 (Flexural Strength after 14 days (on lines of EN 196-1), N/mm^2)	4000.0
ASTM C 109 (Compressive Strength after 1 day (on the lines of ASTM C 109), N/mm^2)	4000.0
ASTM C 109 (Compressive Strength after 3 day (on the lines of ASTM C 109), N/mm^2)	4000.0
ASTM C 109 (Compressive Strength after 14 day (on the lines of ASTM C 109), N/mm^2)	4.0
ASTM C 109 (Compressive Strength after 7 day (on the lines of ASTM C 109), N/mm^2)	4000.0
ASTM C 496 (Splitting Tensile Strength (on the lines of ASTM C 496), N/mm^2)	4000.0
ASTM C 109 (Compressive Strength after 28 day (on the lines of ASTM C 109), N/mm^2)	4000.0
3.2 a of 2645 (Initial setting Time [Comparision with blank sample (IS 4031 / 2645)], min.)	1000.0
3.2 b (Final setting Time [Comparision with blank sample (IS 4031 / 2645)], min.)	1000.0
3.3 a of IS 2645 (Compressive Strength, 3 days [Comparision with blank sample (IS 4031 / 2645)], MPa)	2000.0
3.3 b of IS 2645 (Compressive Strength, 7 days [Comparision with blank sample (IS 4031 / 2645)], MPa)	2000.0
3.1 of IS 2645 (Permeability of water [Comparision with blank sample (IS 4031 / 2645)], ml)	3000.0
IS 101 (Volatile Organic Compound [ VOC - as per IS 101])	4000.0
IS 101 (Toxic Element (Chromium as Cr), by AAS instrumental method.)	1200.0
IS 101 (Toxic Element (Cadmium as Cd), by AAS instrumental method.)	1200.0
IS 2645 (Chloride Content (as per IS 2645 : 2003), %)	1000.0
- - (Wear Resistance Test (on the lines of IS 1237: 2012), loss in mm)	3000.0
IS 101 (Toxic Element (Lead as Pb), by AAS instrumental method.)	1200.0

512

IS 16651 (2017) - High Strength Deformed Stainless Steel Bars and Wires for Concrete Reinforcement - Specification

High Strength Deformed Stainless Steel Bars and Wires for Concrete Reinforcement - Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6.3 (Mass per meter run.)	1000.0
8.6 (Impact Energy)	3000.0
8.7 (Resistance to Intergranular corrosion)	10000.0
9.2 (Tensile Strength (Dia of the bar 0-12 mm))	500.0
9.2 (0.2 percent proof stress)	500.0
9.2 (Percentage Elongation after Fracture.)	500.0
9.2 (Percentage total elongation at maximum force)	500.0
9.3 (Bend Test)	1000.0
9.4 (Re Bend Test)	1000.0
9.2 (Tensile Strength (dia of the bar 12-28 mm))	1500.0
9.2 (Tensile Strength (dia of the bar 28-32 mm))	2000.0
4.3.1 (4) (Carbon (as C))	500.0
4.3.1 (5) (Silicon (as Si))	500.0
4.3.1 (6) (Manganese (as Mn))	500.0
4.3.1 (7) (Sulphur (as S))	500.0
4.3.1 (8) (Chromium (as Cr))	500.0
4.3.1 (9) (Nickel (as Ni))	500.0
4.3.1 (10) (Molybdenum (Mo))	500.0
4.3.1 (11) (Phosphorus (as P))	500.0
4.3.1 (12) (Copper (as Cu))	500.0
4.3.1 (13) (Nitrogen (as N))	500.0

513

A118.3 (1999) - American National Standard Specification for Chemical Resistant Water Cleanable Tile Setting Grouting Epoxy / Epoxy Adhesive

American National Standard Specification for Chemical Resistant Water Cleanable Tile Setting Grouting Epoxy / Epoxy Adhesive

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
E 5.1 (Test for Water Cleanability (Cl E-5.1, ANSI A118.3))	2000.0
E-5.2 (Setting Time and Service Time (Cl E-5.2, ANSI A 118.3))	2000.0
E-5.3 (Test for Shrinkage (Cl E-5.3, ANSI A118.3))	1000.0
E-5.4 (Test for Sag in Vertical Joints (cl 5.4, ANSI A 118.3))	4000.0
E-5.5 (Test for Bond Strength to Quarry Tile (Cl. E-5.5, ANSI A118.3))	9000.0
E-5.6 (Test for Compressive Strength of the cured material (ASTM C 579))	4000.0
E-5.7 (Test for Tensile Strength of the cured material (ASTM C 379))	4000.0
E-5.8 (Test for Thermal Shock (Cl. E-5.8, ANSI A 118.3)))	6000.0
ASTM (Mix Density)	1000.0
Manufacturer Specification (Pot Life (Manufacturer Specified method))	1000.0
Manufacturer Specification (Resistance to intermitted upto 70 Deg C.)	2000.0
ANSI A118.4, H-4.4 (Water Absorption Test (on the lines of ANSI A118.6, Cl. H-4.4))	2000.0

514

EN / ASTM - Flexible Sheet for Water Proofing / Modified Bituminous sheet materials

Flexible Sheet for Water Proofing / Modified Bituminous sheet materials

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
EN 1849-2: 2019, Clause 5 (Thickness (EN 1849-2: 2019, Clause 5), mm)	1000.0
EN 1849-2: 2019, Clause 6 (Mass per Unit area (EN 1849-2: 2019, Clause 6), g/Sq.m)	1000.0
EN 12311-1: 1999, Clause 1-10 (Tensile Force (EN 12311-1: 1999, Clause 1-10), N/5cm)	2000.0
EN 12311-1: 1999, Clause 1-10 (Elongation (EN 12311-1: 1999, Clause 1-10), %)	2000.0
ASTM D5147-14 Clause No. 12 (Low Temperature Flexibility (ASTM D5147-14 Clause No. 12), Visual)	2000.0
ASTM D5147-14 Clause No. 8 (Tear Strength (ASTM D5147-14 Clause No. 8), N)	4000.0
ASTM D5147-14 Clause No. 16 (High Temperature Stability (ASTM D5147-14 Clause No. 16), °C)	1000.0
ASTM D5602-11 Clause No. 1-11 (Puncture Resistance (ASTM D5602-11 Clause No. 1-11), Visual)	2000.0
ASTM D36-14 Clause No. 1-12 (Softening point Of Bitumen (ASTM D36-14 Clause No. 1-12), °C)	1500.0
ASTM D5147-14 Clause No. 11 (Dimensional Stability(ASTM D5147-14 Clause No. 11), %)	2000.0

515

Custom ASTM - Non Shrinking Grouts / Mortar - Method of Test ASTM

Non Shrinking Grouts / Mortar - Method of Test ASTM

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
ASTM C 1006 (Test for Tensile Splitting Strength (Tensile Splitting Strength after 28 days), N/mm^2)	4000.0
ASTM C 531 (Test for Coefficient of Linear Thermal Expansion, mm/mm/Deg C (ASTM C 531))	2000.0
Manufacture Specified (Pot Life, in minutes (as per manufacturer specification).)	1000.0
ASTM (Density (Dry Loose Bulk Density/Dry Compacted Density/Wet Mix Density))	2000.0
ASTM C 881 (Test for Slant Shear Strength (14 Days), N/mm^2)	4000.0
ASTM D 7234 (Test for Pull Out Adhesion Strength (28 Day Strength), N/mm^2 [ASTM D 7234])	5000.0
ASTM D 7234 (Test for Pull Out Adhesion Strength (7 Day Strength), N/mm^2 [ASTM D 7234])	5000.0
ASTM C 307 (Test for Tensile Strength (28 Day Tensile Strength), N/mm^2 [ASTM C 307])	4000.0
ASTM C 307 (Test for Tensile Strength (7 Day Tensile Strength), N/mm^2 [ASTM C 307])	4000.0
ASTM C 348 (Test for Flexural Strength (28 Day Flexural Strength), N/mm^2 [ASTM C 348])	4000.0
ASTM C 348 (Test for Flexural Strength (7 Day Flexural Strength), N/mm^2 [ASTM C 348])	4000.0
ASTM C 109 (Test for Compressive Strength (28 Day Compressive Strength), N/mm^2 [ASTM C 109])	4000.0
ASTM C 109 (Test for Compressive Strength (7 Day Compressive Strength), N/mm^2 [ASTM C 109])	4000.0
ASTM C 109 (Test for Compressive Strength (3 Day Compressive Strength), N/mm^2 [ASTM C 109])	4000.0
ASTM C 109 (Test for Compressive Strength (1 Day Compressive Strength), N/mm^2)	4000.0
IS 4031 (Part 10) (Drying Shrinkage Test, Drying Shrinkage (on lines of IS 4031 -Part 10))	1000.0
Cl 7 of ASTM C 496 (Splitting Tensile Strength after 28 days, N/mm^2 (on the lines of ASTM C 496 : 2004))	4000.0
ASTM (Compacted Bulk Density, kg/m^3)	1000.0
ASTM C 293 (Test for Flexural Strength (on the lines of ASTM C 293 - 02 with sample preparation),)	9000.0
ASTM C 293 (Test for Flexural Strength (on the lines of ASTM C 293 - 02 with sample preparation),)	9000.0
ASTM C 293 (Test for Flexural Strength (on the lines of ASTM C 293 - 02 on prepared samples),)	4000.0
ASTTM C 293 (Test for Flexural Strength (on the lines of ASTM C 293 - 02 with sample preparation) after 14 days, N/mm^2)	9000.0
ASTM C 109 (Test for Compressive Strength (on the lines of ASTM C 109) after 14 days, N/mm^2)	4000.0
Cl 7 of ASTM C 496 (Splitting Tensile Strength after 28 days, N/mm^2 (on the lines of ASTM C 496 : 2004))	4000.0
- - (Test for Flexural Strength after 28 days (on the lines of ASTM C 78), N/mm^2)	4000.0
- - (Test for compressive strength after one day, N/mm^2)	4000.0
- - (Test for compressive strength, 28 days, in N/mm^2)	4000.0
- - (Test for Tensile Strength (Split) after 28 days (on the lines of ASTM C 496), N/mm^2)	4000.0

516

IS 6419 (1996) - Welding rods and bare electrodes for gas shielded arc welding of structural steel - Specification (First Revision)

Welding rods and bare electrodes for gas shielded arc welding of structural steel - Specification (First Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
14.3.3 (All weld Impact test)	3000.0
14.3.2 (All weld Tensile test)	3000.0
14.3.1 (Preparation of Weld assembly)	5000.0
14.2 (Radiography Test)	1000.0
10.2.3 (Helix)	500.0
10.2.2 (Cast)	500.0
10.2.1 (Temper)	1000.0
10.1 (Finish)	500.0
8.1 (Dimension of Spools)	500.0

517

Custom specification NTH WR General Chemicals - Custom specification NTH WR General Chemicals

Custom specification NTH WR General Chemicals

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Resistance to spent wash)	1500.0
- (Annexure for Organic Fertilizer)	10000.0

518

Custom specification NTH WR Metal Sample - Custom specification NTH WR Metal Sample (OES)

Custom specification NTH WR Metal Sample (OES)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Custom specification NTH WR Metal Sample (Please referred annexure)	5000.0
custom specification NTH WR Metal OES (Carbon (C))	700.0
custom specification NTH WR Metal OES (Manganese (Mn))	700.0
custom specification NTH WR Metal OES (Silicon (Si))	700.0
custom specification NTH WR Metal OES (Sulphur (S))	700.0
custom specification NTH WR Metal OES (Phosphorus (P))	700.0
custom specification NTH WR Metal OES (Nickel (Ni))	700.0
custom specification NTH WR Metal OES (Molybdenum (Mo))	700.0
custom specification NTH WR Metal OES (Chromium (Cr))	700.0
custom specification NTH WR Metal OES (Titanium (Ti))	700.0
custom specification NTH WR Metal OES (Aluminium (as Al))	500.0
custom specification NTH WR Metal OES (Boron (as B))	500.0
custom specification NTH WR Metal OES (Mass of Zinc Coating)	1500.0
Custom specification NTH WR Metal Sample (Thickness of material (Aluminum and Copper))	2000.0
Custom specification NTH WR Metal Sample (Nature (Visual Examination))	1000.0

519

Custom specification NTH WR IS 101 & other paint - Custom specification NTH WR IS 101 & other paint test methods

Custom specification NTH WR IS 101 & other paint test methods

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Custom specification NTH WR IS 101 & other paint (Please referred annexure for the test result)	6000.0
Custom specification NTH WR IS 101 & other paint (Volatile Organic Compounds (VOC))	4000.0
Custom specification NTH WR IS 101 & other paint (pH)	1200.0
Custom specification NTH WR IS 101 & other paint (Volume Solids (IS 101 (Part 8/Sec 6) : 1993))	2000.0
Custom specification NTH WR IS 101 & other paint (Lead as (Pb))	1200.0
Custom specification NTH WR IS 101 & other paint (Wet opacity)	1200.0
Custom specification NTH WR IS 101 & other paint (Pull of Adhesion (ASTM D 4541))	2000.0
Custom specification NTH WR IS 101 & other paint (Resistance to Alkali (Annex F IS 15489 : 2013))	1500.0
Custom specification NTH WR IS 101 & other paint (Toxic element: Chromium (VI) Atomic Absorption Spectrophotometric methods)	1200.0
Custom specification NTH WR IS 101 & other paint (Toxic element: Cadmium, Atomic Absorption Spectrophotometric methods)	1200.0
Custom specification NTH WR IS 101 & other paint (Toxic element: Mercury, Atomic Absorption Spectrophotometric methods)	1200.0
Custom specification NTH WR IS 101 & other paint (Drying Time: Surface dry)	1200.0
Custom specification NTH WR IS 101 & other paint (Drying time: Hard dry)	1200.0
Custom specification NTH WR IS 101 & other paint (Consistency)	1200.0
Custom specification NTH WR IS 101 & other paint (Accelerated storage stability at 60(+/- 2) deg.c)	3000.0
Custom specification NTH WR IS 101 & other paint (IMPACT RESISTANCE)	1500.0
Custom specification NTH WR IS 101 & other paint (Water Vapor Transmission (ASTM D 1653))	5000.0
Custom specification NTH WR IS 101 & other paint (Water Vapor Transmission)	5000.0
Custom specification NTH WR IS 101 & other paint (Flash Point (IS 101 (Part 1/Sec 6):1987)	1200.0
Custom specification NTH WR IS 101 & other paint (Abrasion Resistance, 1000 cycle, 1 kg load, (ASTM D 4060))	2000.0
Custom specification NTH WR IS 101 & other paint (Salt Spray test (IS 101 (Part 6/Sec 1) for 150 hrs)	6000.0
Custom specification NTH WR IS 101 & other paint (Durability: Accelerated Weathering Test by Xenon Arc for 150 hrs)	9000.0
Custom specification NTH WR IS 101 & other paint (Appearance (Visual))	1200.0
Custom specification NTH WR IS 101 & other paint (Specific Gravity @ 30 Deg. C.)	1200.0
Custom specification NTH WR IS 101 & other paint (Colour (Visual))	1200.0
Custom specification NTH WR IS 101 & other paint (Surface Drying Time @ 30 Deg. C (IS 101 (Part 3/Sec 1)) - 1986)	1200.0
Custom specification NTH WR IS 101 & other paint (Non Volatile Matter (Solid Content))	1200.0
Custom specification NTH WR IS 101 & other paint (Dry Film Thickness per coat, By Brush (IS 101 (Part 3/Sec 2)-89)	1200.0
Custom specification NTH WR IS 101 & other paint (Finish (IS 101 (Part 3/Sec 4)))	1200.0
Custom specification NTH WR IS 101 & other paint (Pencil Hardness (IS 101 (Part 5/Sec 1))-1988)	1200.0
Custom specification NTH WR IS 101 & other paint (Flexibility and adhesion (IS 101 (Part 5/Sec 2))-1988)	1200.0
Custom specification NTH WR IS 101 & other paint (Scratch Hardness, 1 kg load (IS 101 (Part 5/Sec. 2)-1988)	1200.0
Custom specification NTH WR IS 101 & other paint (Finish (IS 101 (Part 3/Sec 4)))	1200.0
Custom specification NTH WR IS 101 & other paint (Gloss 60 deg Angle (IS 101 (Part 4/Sec 4))	1200.0
Custom specification NTH WR IS 101 & other paint (Gloss 45 deg Angle (IS 101 (Part 4/Sec 4))	1200.0
Custom specification NTH WR IS 101 & other paint (Mass per 10 liters ((IS 101 (Part 1/Sec 7) : 2020))	1200.0
Custom specification NTH WR IS 101 & other paint (Volatile matter (IS 101 (Part 2/Sec 2) ))	1200.0
Custom specification NTH WR IS 101 & other paint (Stain Resistance Test (ASTM D 4828))	5000.0
IS 101 paint custom specification (Silver content by AAS method)	1200.0
Custom specification NTH WR IS 101 & other paint (Ash content (ASTM D 1650))	1500.0
Custom specification NTH WR IS 101 & other paint (Non volatile content (ISO 3251))	1200.0
Custom specification NTH WR IS 101 & other paint (Volatile Content (ISO 3251))	1200.0
RDSO (RDSO, Please see the annexure for test)	3000.0
Custom specification NTH WR IS 101 & other paint (Theoretical covering capacity)	1200.0
Custom specification NTH WR IS 101 & other paint (Binder Content (Active content) by Ignition Method)	1200.0
Custom specification NTH WR IS 101 & other paint (Water absorption test for 1 hr (ASTM D 570))	1500.0
Custom specification NTH WR IS 101 & other paint (WHITE CEMENT BASED POWDER PUTTY)	19400.0
Custom specification NTH WR IS 101 & other paint (ACRYLIC POWDER PUTTY)	19400.0
Custom specification NTH WR IS 101 & other paint (Pull off Adhesion Test (ASTM D 4541))	2000.0
Custom specification NTH WR IS 101 & other paint (Flexibility & Adhesion (ASTM D 522))	1200.0
Custom specification NTH WR IS 101 & other paint (Volume Solid (ASTM D 2697))	2000.0
Custom specification NTH WR IS 101 & other paint (Drying Time : Touch dry (ASTM D 1640))	1200.0
Custom specification NTH WR IS 101 & other paint (Drying Time: Hard Dry (ASTM D 1640))	1200.0
Custom specification NTH WR IS 101 & other paint (Cathodic disbandment @ Room temperature for 30 days (ASTM G 42))	10000.0
Custom specification NTH WR IS 101 & other paint (Water Resistance (Immersion))	1500.0
Custom specification NTH WR IS 101 & other paint (Cyclic corrosion test, 1008 hours, Salt Spray: 72 hrs, Drying in air: 16 hrs, UVA-340: 80 hrs One cycle: 168 hrs X 6 cycles (ASTM D 5894))	46080.0
Custom specification NTH WR IS 101 & other paint (UV Resistance - 100hrs)	6000.0
Custom specification NTH WR IS 101 & other paint (Abrasion Resistance, (1 Kg load, 1000 cycles, Wheel CS-10) , (ASTM D 4060))	2000.0
Custom specification NTH WR IS 101 & other paint (Impact Resistance (ASTM D 2794))	1500.0
Custom specification NTH WR IS 101 & other paint (Chemical resistance test for 24 hrs 10% HCl (ASTM D 543))	1500.0
Custom specification NTH WR IS 101 & other paint (Chemical Resistance Test for 24 hrs, 10% H2SO4 (ASTM D 543))	1500.0
Custom specification NTH WR IS 101 & other paint (Salt spray test for 1000 hrs (ASTM B 117))	30000.0
Custom specification NTH WR IS 101 & other paint (Temperature resistance @ 200 Deg C (ASTM D 2485 Method A))	2000.0
Custom specification NTH WR IS 101 & other paint (Viscosity by Flow cup (B-4), IS 101 (Part 1/Sec 5))	1200.0
Custom specification NTH WR IS 101 & other paint (Low temperature flexibility after 1000 hrs)	7000.0
Custom specification NTH WR IS 101 & other paint (Low and High Service Temperature Limits)	5000.0
Custom specification NTH WR IS 101 & other paint (Accelerated Weathering Test, U V Lamp (ASTM D 154) for 700 hrs)	42000.0
Custom specification NTH WR IS 101 & other paint (Resistance to Salt spray (ASTM B 117 for 500 hrs))	15000.0
Custom specification NTH WR IS 101 & other paint (Determination of Fineness of grind ((IS 101 (Part 3/ Sec 5): 2022)	1200.0
Accelerated Weathering Tests (Accelerated Weathering Tests (UV condensation type), IS 101 (Part 6/Sec 5): 1997 for 500 hr)	30000.0
Accelerated Weathering Tests (Accelerated Weathering Tests (UV condensation type), IS 101 (Part 6/Sec 5): 1997 for 1000 hr)	60000.0
Accelerated Weathering Tests (Accelerated Weathering Tests (UV condensation type), IS 101 (Part 6/Sec 5): 1997 for 1500 hr)	90000.0
Accelerated Weathering Tests (Accelerated Weathering Tests (UV condensation type), IS 101 (Part 6/Sec 5): 1997 for 2000 hr)	120000.0
Salt spray test (Salt spray test for 500 hrs (IS 101 (Part 6/Sec 1): 1988)	20000.0
Salt spray test (Salt spray test for 1000 hrs (IS 101 (Part 6/Sec 1): 1988)	40000.0
Custom specification NTH WR IS 101 & other paint (Viscosity by B 4 Flow Cup (IS 101 Part 1/Sec 5))	1200.0
Custom specification NTH WR IS 101 & other paint (Tack Free Drying Time (IS 101 Part 3/Sec 1))	1200.0
Custom specification NTH WR IS 101 & other paint (Coverage)	1500.0
Custom specification for paint samples (MEK Rub Test (ASTM D 5402))	1500.0
Custom specification for Paint Samples (Self-life (As per customer declaration))	1200.0
Custom specification for paint samples (Anti Grafiti Test (ASTM D 6578))	3000.0
Custom specification for paint samples (Identification of Material by FTIR)	2000.0
custom specification IS 101 (Volume Capacity of SS cup)	2000.0
- (Overcoating interval)	1200.0
Free formaldehyde (Free formaldehyde (ASTM D 6191))	5000.0
Custom specification NTH WR IS 101 & other paint test methods (Please refer the annexure for test results)	6000.0
Custom specification NTH WR IS 101 & other paint test methods (Please refer the annexure for the test result)	8400.0
Custom specification NTH WR IS 101 & other paint test methods (Please refer the annexure for the test result)	12000.0
Custom specification NTH WR IS 101 & other paint test methods (Please refer the annexure for the test result)	18000.0
Custom specification NTH WR IS 101 & other paint test methods (Please refer annexure for the test result)	24000.0
Custom specification NTH WR IS 101 & other paint test methods (Please refer annexure for the test result)	30000.0
Custom specification NTH WR IS 101 & other paint test methods (Please refer annexure for the test result)	32700.0

520

Custom specification NTH WR Two Component Paint & Coating System - Specification for Surface preparation and protective coating paint

Specification for Surface preparation and protective coating paint

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (Please referred annexure)	1.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (Water vapour permeability)	5000.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (Flash Point)	1200.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (Volume Solid (ISO 3233))	2000.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (Dry Film Thickness (DFT) Per Coat)	1200.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (Theortical Coverage capacity)	1200.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (Weight per liter (Mix paint) (ISO 2811))	1200.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (Specific Gravity (Base) (ISO 2811))	1200.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (Specific gravity (Hardner) (ISO 2811))	1200.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (Touch Dry @ 30 deg. C (ASTM D 1640))	1200.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (Hard Dry @ 30 Deg. C (ASTM D 1640))	1200.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (Full Cure @ 30 Deg. C (ASTM D 1640))	1200.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (Over coating interval (ASTM D 1640))	1200.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (Pot Life @ 30 deg. C.)	1500.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (Pull Off Adhesion Test (ASTM D 4541))	2000.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (Abrasion Resistance, (1kg load, 1000 cycles, Wheel CS-17) (ASTM D 4060))	3000.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (Temp Resistance (ASTM D 2485 Method A))	5000.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (Temp Resistance (ASTM D 2485 Method B))	18000.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (Ash content (Mix paint) (ASTM D 1650))	1.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (Non Volatile Matter (ISO 3251))	1200.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (Volatile Matter (Mix Paint))	1200.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (100% Humidity test, duration 1440 hrs (ASTM D 2247))	45000.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (Thermal Shock Resistance Test (Method A): 5 cycles @ 30 minutes in furnace at 120 deg. C and 15 min in water after quenching in water for each cycle. (ASTM D 2485 Method A))	5000.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (Cathodic disbondment Test (ASTM G8 @ 30 days, Temp 20-30 deg.C))	10000.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (Volume Solid (ASTM D 2697))	2000.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (Tensile Strength after curing at 80 deg C for 8 hours (ASTM D 638))	2000.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (Elongation at break after curing at 80 deg C for 8 hours (ASTM D 638))	2000.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (Morten Heat Distortion Temperature test)	1500.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (Water Absorption test)	1500.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (Zinc Content (% Solid by mass) ASTM D 521)	2000.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (Tensile Strength (ASTM D 638))	2000.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (% Elongation (ASTM D 638))	2000.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (Solid content (ISO 3233))	1200.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (Impact Resistance (ASTM D 2794))	1500.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (Water absorption (Immersion 30 days, ASTM D 570))	2000.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (Salt Spray Test (5% NaCl solution @ 35 deg C) 1440 hrs)	57600.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (Holiday test (ASTM D 5162))	2000.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (Cyclic Test 4200 hrs:- Salt Spray : 72 hrs., Drying in air : 16 hrs., UV-A340 nm weather meter: 80 hrs. One cycle: 168 hrs. (25 cycles at 168 hrs. each cycle)(ASTM D5894))	200000.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (Chemical Resistance Test (ASTM D 543) a) 10% NaOH 1000 hrs)	5000.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (Chemical Resistance Test (ASTM D 543) b) 40% NaOH 1000 hrs)	5000.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (Chemical Resistance Test (ASTM D 543) c) 5% H2SO4 168 hrs)	2000.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (Chemical Resistance Test (ASTM D 543) d) Xylene 4 weeks)	3000.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (Chemical Resistance Test (ASTM D 543) e) Acetone 4 weeks)	3000.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (Chemical Resistance Test (ASTM D 543) f) Ethanol 4 weeks)	3000.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (Chemical Resistance Test (ASTM D 543) g) Kerosene 4 weeks)	3000.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (Chemical Resistance Test (ASTM D 543) Water Immersion Sea/DM Water, 2000 hrs.)	5000.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (Immersion in DM/DI water @ 90 Deg C for 30days (ASTM C 868))	5000.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (Cathodic disbondment test @ 60 deg C for 30 days (ASTM G8))	12000.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (Hardness: Shore D (ASTM D 2240))	2000.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (APPERANCE)	1200.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (Water Resistance (Water Immersion) @ 30 Deg C for 30 Days (ASTM D 870))	3000.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (Tensile Strength and Elongation @ break as per ASTM test method)	4000.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (Abrasion Resistance, (1kg load, 1000 cycles, Wheel H-18) (ASTM D 4060))	3000.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (FINISH)	1200.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (Pencil Hardness test (ASTM D 3363))	1500.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (Dry Film Thickness (DFT) , ASTM D 1186)	1200.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (Water Penetration (DIN 1048))	10000.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (Water Vapour Transmission (ASTM D 1653))	5000.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (Viscosity at 30 Deg C (ASTM D 5125))	1200.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (Specific gravity at 30 Deg C (ASTM D 891))	1200.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (Non Volatile Matter (Mix Paint) (ASTM D 1353))	1200.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (Pot Life (ASTM D 562))	1500.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (Recoatability (IS 101))	1200.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (UV Resistance for 2000hrs (Xenon arc air cool weatherometer) ASTM G 155)	120000.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (Number of coats)	1200.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (Tensile strength (ASTM D 2370))	2000.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (Elongation (%) (ASTM D 2370))	2000.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (Shelf Life)	1200.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (Scratch Hardness Test)	1200.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (Adhesion by Tape Test (ASTM D 3359))	1500.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (Salt spray test (ASTM B 117) for 1000 hrs.)	40000.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (Xenon Arc lamp Weatherometer (ASTM G 155) for 1000 hrs)	60000.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (Chemical Resistance- 10% H2SO4 for 7 days, Room temperature (ASTM D 543))	1500.0
Chemical resistance (Chemical Resistance - 30% NaOH for 7 days, Room temperature (ASTM D 543))	1500.0
Chemical resistance (Chemical resistance - Deionized water for 7 days, Room temperature (ASTM D 543))	1500.0
Humidity Resistance (Humidity Resistance - for 5000 hrs (ASTM D 2247))	138889.0
Water immersion (Pull off adhesion after High Temperature Water immersion - for 28 days @ 80 Deg C (ASTM D 543))	32000.0
Cathodic disbonding (Cathodic disbonding test- 7 days @ 95 Deg C (ASTM G 42/ ASTM G 8))	10000.0
Salt spray test (Resistance to salt spray - for 10000 hours (ASTM B 117))	300000.0
Pull off adhesion test (Pull off adhesion test after hot water immersion for 100 days @ 95 Deg C (ASTM D 4541 & ASTM D 543))	72000.0
Cathodic disbonding (Cathodic disbonding test- for 30days @ 95 Deg C (ASTM G 42/ ASTM G 8))	20000.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (Thermal ageing for 100 days at 150 Deg. C followed by adhesion test (ASTM D 4541/ISO 10289))	42000.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (Cathodic disbonding test- for 15 days @ 95 Deg C (ASTM G 42/ ASTM G 8))	15000.0
Two component paint (Immersion test - 5% Acetic Acid for 30 Days (ASTM D 543))	3000.0
TWO COMPONENT Paint & coating system (Immersion test - 25% H2SO4 for 30 days (ASTM D 543))	3000.0
TWO COMPONENT Paint & coating system (Immersion Test- 25% Na2Co3 for 30 days (ASTM D 543))	3000.0
TWO COMPONENT Paint & coating system (Immersion Test - 10% NaCl for 30 days (ASTM D 543))	3000.0
TWO COMPONENT Paint & coating system (Immersion Test - 25% NaOH for 30 days (ASTM D 543))	3000.0
TWO COMPONENT Paint & coating system (Immersion Test- 25 % Acetic Acid for 30 days (ASTM D 543))	3000.0
TWO COMPONENT Paint & coating system (Immersion Test- 25 % HCl for 30 days (ASTM D 543))	3000.0
TWO COMPONENT Paint & coating system (Immersion Test - 25 % HNO3 for 30 Days (ASTM D 543))	3000.0
TWO COMPONENT Paint & coating system (Ultraviolet (UV) Lamp Apparatus (Accelerated Weathering Tester) Lamp UV 313, 500 hrs)	30000.0
Custom specification NTH WR TWO COMPONENT Paint & coating system Specification (Resistance to humid poultice (Cataplasm test) (BS EN 13523 Part 27 : 2017))	10000.0
TWO COMPONENT Paint & coating system (Water Content (IS 101 (Part 2/Sec 1) : 2018)	1200.0
TWO COMPONENT Paint & coating system (Drying time Tack Free @ 30 deg.C)	1200.0
TWO COMPONENT Paint & coating system (Fastness to Light 100 Hrs (IS 101 (Part 4/Sec 3) : 1988)	5000.0
Paint coating (Ultraviolet (UV) Lamp Apparatus (Accelerated Weathering Tester) Lamp UV 313, 1000 hrs (Cycle: 4 hrs UV & 4 hrs condensation))	60000.0
Surface coating paint system (Thermal Stability Test (ASTM D 2485))	1500.0
Surface Coating System (Pull off adhesion test after thermal shock (ASTM D 4541))	2000.0
Two component paint system (Surface Dry (ASTM D 1640))	1200.0
Two component paint system (Sag Resistance)	2000.0
Two component paint system (Adhesion by Hatch Cut (ASTM D 3359 method B))	2000.0
Two component paint (Specific Gravity Mix Paint @ 30 Deg C)	1198.0
Two component paint (Volatile Organic Compound (VOC))	4000.0
Two component paint (Viscosity base, by B4 flow cup)	1200.0
Two component paint (Viscosity Hardener by B4 flow cup)	1200.0
Two component paint (Viscosity mix paint by B4 flow cup)	1200.0
Specification for Surface preparation and protective coating (Please refer annexure for the test results)	79420.0
Inorganic Zinc Silicate Paint (Please see the annexure for the test result:)	118450.0
Specification for Surface preparation and protective coating (Two Component Paint & Coating System) (Salt Spray Test for 1440 hrs)	57600.0
Specification for Surface preparation and protective coating (Two Component Paint & Coating System) (Water absorption for immersion of 30 days at 65 Deg.C)	7000.0
Specification for Surface preparation and protective coating (Two Component Paint & Coating System) (Epoxy equivalent (Resin))	2000.0
Two component paint system (Chemical Resistance to continuous immersion in Seawater for 30 days)	2999.0
Custom specification NTH WR Two Component Paint & Coating System (Abrasion resistance - Weight 1000 gms, Cycles 5000, Wheel CS-17)	4997.0
Specification for Surface preparation and protective coating (Two Component Paint & Coating System) (Impact Test)	1500.0
RDSO M&C/ PCN/ 100/ 2018 (2018) - Specification for Epoxy Cum Polyurethane Painting System (Two Pack) for the Exterior Painting of Railway Coaches (Please refer annexure for the test result (Table 1 for full Gloss Polyurethane Enamel Two Pack) except for the parameter Unreacted monomer)	21000.0
Specification for Surface preparation and protective coating (Two Component Paint & Coating System) (cathodic disbondment test ASTM G42 at 80 Deg C)	10000.0
Specification for Surface preparation and protective coating (Two Component Paint & Coating System) (Cathodic Disbondment Test)	10000.0
Specification for Surface preparation and protective coating (Two Component Paint & Coating System) (WEATHERING TEST Xenon Arc/UV for 100 hrs)	6000.0
Custom specification NTH WR Two Component Paint & Coating System (Chemical resistance test - 30% NaOH, for 30 days (ASTM D 543))	3000.0
Custom specification NTH WR Two Component Paint & Coating System (Chemical resistance test - 30% NaCl, for 30 days (ASTM D 543))	3000.0
Custom specification NTH WR Two Component Paint & Coating System (Chemical resistance test - 10% H2SO4, for 30 days (ASTM D 543))	3000.0
Custom specification NTH WR Two Component Paint & Coating System (Chemical resistance test - Diesel, for 30 days (ASTM D 543))	4000.0
Custom specification NTH WR Two Component Paint & Coating System (Water Absorption test for 63 days (ASTM D 570))	3000.0
Custom specification NTH WR Two Component Paint & Coating System (Humidity Resistance, 1000hrs (ASTM D 4585))	30000.0
Custom specification NTH WR Two Component Paint & Coating System (Cathodic disbandment, 28 day (ASTM G 95))	10000.0
- (Water absorption at ambient temperature (ASTM D 570))	2000.0
- (Water absorption at temperature 65 Deg. C. (ASTM D 570))	7000.0
Chemical resistance (Chemical resistance : 50% Sulphuric acid, 168 hrs)	3000.0
Chemical resistance (Chemical resistance : 37% HCl, 168 hrs)	3000.0
Chemical resistance (Chemical resistance : 50% Nitric Acid, 168 hrs)	3000.0
Custom specification NTH WR Two Component Paint & Coating System (Ash content (Base), ASTM D 1650)	1200.0
Custom specification NTH WR Two Component Paint & Coating System (Ash content (Hardener), ASTM D 1650)	1200.0
Custom specification NTH WR Two Component Paint & Coating System (Non volatile matter (Base) ISO 3251)	1200.0
Custom specification NTH WR Two Component Paint & Coating System (Non volatile matter (Hardener) ISO 3251)	1200.0
Custom specification NTH WR Two Component Paint & Coating System (Volatile matter (Base), ASTM D 2369)	1200.0
Custom specification NTH WR Two Component Paint & Coating System (Volatile Matter (Hardener), ASTM D 2369)	1200.0
Custom specification NTH WR Two Component Paint & Coating System (Spectral data of film by FTIR)	2000.0
Two Component Paint & Coating System (Volume solid)	1999.0
Two Component Paint & Coating System (Pigment content)	1500.0
Two component paint system & Surface coating material (Zinc Poshphate in the total pigment content)	1500.0
Two Component Paint & Coating System (NVM)	1200.0
Two Component Paint & Coating System (Lamellar MIO)	1500.0
Two Component Paint & Coating System (Phthallic anhydride content of non-volatile vehicle)	2000.0
Two Component Paint & Coating System (Accelerated storage stability test at 60 Deg C, 96 hours)	3000.0
Two Component Paint & Coating System (Red oxide (as Fe2O3) in total pigment)	1500.0
Two Component Paint & Coating System (Metallic Zinc content)	1500.0

521

EIL B224-000-79-41-PLS-01 : Part 5 (2019) - Job specification for surface preparation and protective coating

Job specification for surface preparation and protective coating

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found

522

OPTICAL FIBER CABLE - OPTICAL FIBER CABLE

OPTICAL FIBER CABLE

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Marking)	500.0
2 (Description of Optical Fiber Cable)	500.0
3 (Marking on Optical Fiber Cable)	500.0
4 (Construction of Optical Fiber Cable)	500.0
4.1(a) (Nos of Fiber and Colour)	1000.0
4.1(b) (Presence of Sheath/Covering in addition to coat on Fiber)	500.0
4.1(c) (Individual Sheathed of Fiber Cable)	8000.0
4.1(d) (Colour of Sheath)	500.0
4.1(e) (Mylar Fiber and Colour)	500.0
4.1(f) (Any other Detail of fiber cable)	500.0
4.1(g) (Colour of Jacket)	500.0
4.1(h) (Overall Diameter of Jacket)	500.0
4.1(i) (Transmission of Light Test of Fiber Cable)	1000.0
1 (Customs Specification)	30000.0
El/1 (confirms the plastic material against individual Fiber)	45000.0

523

IS 13730 Part 29 and IEC 317-0-2 - WINDING WIRES OF POLYESTER OR POLYESTERIMIDE OVERCOATED WITH POLYAMIDE-IMIDE ENAMELLED RECTANGULAR COPPER WIRE

WINDING WIRES OF POLYESTER OR POLYESTERIMIDE OVERCOATED WITH POLYAMIDE-IMIDE ENAMELLED RECTANGULAR COPPER WIRE

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4,5,6,7,8,9,12,13 (Tests as per IS 13730 Part 29 & IEC 317-0-2 as given in Annexure)	15000.0

524

IS 12943:1990 - Brass Glands for PVC Cables

Brass Glands for PVC Cables

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5 (Possible Tests as per Annexure)	75000.0

525

IS 12943/ BS: 62444:2013 & BS:6121-1-2005 - Cable Glands for Electrical Installations

Cable Glands for Electrical Installations

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
9,10,12,4.2.2 , 4.2.1, 4.2.3 (Possible Tests as per Annexure)	45000.0

526

IS 13730 : Part 27 (2018) - Specifications for Particular Types of Winding Wires Part 27 Paper Tape Covered Rectangular Copper Wire ( First Revision )

Specifications for Particular Types of Winding Wires Part 27 Paper Tape Covered Rectangular Copper Wire ( First Revision )

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
3.2.2 (Sizes)	-

527

Custom specification Paint coating - Custom specification Paint coating Fire retardant test as per customer requirement

Custom specification Paint coating Fire retardant test as per customer requirement

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Custom specification for paint coating (Surface flame spreading/fire retardant test for 0 -1 hour)	3000.0
Custom specification for paint coating (surface flame spreading/fire retardant test for 1 - 2 hours)	5000.0
Custom specification fire retardant paint-4 Hrs. (Surface flame spreading/fire retardant test for 3 - 4 hours)	10000.0
Custom specification fire retardant paint-3 Hrs. (Surface flame spreading/fire retardant test 2 - 3 hours as per customer requirement)	7000.0

528

BS:6121-1: 2005 - Armour Cable Glands

Armour Cable Glands

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4.2.2 , 4.2.1, 4.2.3 (Applicable parameters as per Annexure)	150000.0

529

IS 383 for fine aggregate (2016) - Coarse and fine aggregate for Concrete

Coarse and fine aggregate for Concrete

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Sieve analysis/Particle size distribution ( IS:2386(part -1)1963)	2000.0
2 (Test for Specific Gravity (IS:2386(part -III)1963))	500.0
3 (Test for Water absorption (IS:2386(part -III)1963))	1000.0
4 (Test for Bulk Density-Loose condition ( IS:2386(part -III)1963))	500.0
5 (Test for Bulk Density-Compacted condition ( IS:2386(part -III)1963))	500.0
6 (Test for Silt content- (CPWD Specification))	1000.0
7 (Deleterious Materials)	2000.0
8 (Test for Soundness of Aggregate (IS 2386(Part 5):1963))	2000.0
9 (Test for Alkali aggregate reaction- Chemical method (IS 2386(Part 7):1963))	3000.0
10 (Test for bulking of sand)	1000.0
5.5 (Soundness of Aggregates [IS 2386 (Part 5)], %)	2000.0
Clause 5.7 Table 3 (TOTAL ALKALI CONTENT as Na2O EQUIVALENT)	1200.0
5.7 TABLE 3 (TOTAL SULPHATE CONTENT as SO3)	1200.0
5.7 TABLE 3 (ACID SOLUBLE CHLORIDE CONTENT)	1200.0
5.2 (Organic Impurities)	1000.0

530

ASTM D 4541 - Standard Test Method for Pull-Off Strength of coatings using portable adhesion Tester

Standard Test Method for Pull-Off Strength of coatings using portable adhesion Tester

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
ASTM D 4541 (pull-off strength of coatings (Pull of Adhesion, ASTM D 4541))	2000.0

531

ASTM D 4541 (2017) - Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers

Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (1)	-

532

IS 7098 : Part 2 (2011) - Crosslinked polyethylene insulated thermoplastic sheathed cables - Specification: Part 2 for working voltages from 3.3 kV up to and including 33 kV (Second Revision)

Crosslinked polyethylene insulated thermoplastic sheathed cables - Specification: Part 2 for working voltages from 3.3 kV up to and including 33 kV (Second Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
19.1 (i) d) (Dimensions)	1000.0
8.1 (Conductor)	100.0
19.2.(j) (High Voltage test at room temperature)	1000.0
13.1 (Insulation)	100.0
19.2.(g) (Tensile strength at break)	1000.0
19.1.(xv) (Flammability Test)	500.0
19.1.(iii) a) (Tensile strength at break)	1000.0
19.2.(d) (Resistance of conductor-R)	1000.0
19.2 (Acceptance Test)	25000.0
19.2.(d) (Resistance of conductor-Y)	1000.0
19.1.(vi)(g) (Thermal stability)	5000.0
19.2.(d) (Resistance of conductor-B)	1000.0
19.2.(d) (Resistance of conductor-Black)	250.0

533

Polymer Identification by FTIR Method - Fourier-transform infrared spectroscopy (FTIR) instrumental technique for identification

Fourier-transform infrared spectroscopy (FTIR) instrumental technique for identification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
FTIR Method (Polymer Identification by FTIR Method / Library)	2000.0

534

Custom specification for paint as per IS 101 (1988) - Methods of Sampling and Test for Paints, Varnishes and related products

Methods of Sampling and Test for Paints, Varnishes and related products

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
(Part 4/Sec 3):1988 (Optical Tests: Light Fastness Test for 100 hrs)	5000.0
Thickness (Coating Thickness)	1200.0
Water absorption (Water absorption)	1.0
Water Repellency test (Water Repellency test)	1.0

535

IS 1148 (2009) - Steel Rivet Bars (medium And High Tensile)--For Structural Purposes--For Structural Purposes

Steel Rivet Bars (medium And High Tensile)--For Structural Purposes--For Structural Purposes

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
11 (Yield Stress ( Medium) - 6mm up to and including 12mm)	1000.0
11 (Yield Stress (Medium)- Over 12mm up to and including 20mm)	1000.0
11 (Yield Stress (Medium)- Over 20 mm up to and including 40mm)	1000.0
11 (Tensile Strength (Medium))	1000.0
11 (Elongation ( Medium Tensile Steel))	1000.0
11 (Tensile Strength (High))	1000.0
11 (Yield Stress ( High) - 6mm up to and including 12mm)	1000.0
11 (Yield Stress( High) - Over 12mm up to and including 20mm)	1000.0
11 (Yield Stress (High) - Over 20mm up to and including 40mm)	1000.0
11 (Elongation (High tensile steel))	1000.0
12 (Bend Test)	2000.0
8 (Dimension)	500.0
9 (Diameter of Bar ( below 20mm ))	500.0
7 (Visual Observation)	1000.0
6 (Carbon)	500.0
6 (Sulphur)	500.0
6 (Phosphorus)	500.0

536

MORTH 803 Thermoplastic Road Marking Material MORTH-5th Revision 2013 (2013) - Ministry of Road Transport and Highways - Specifications form Road And Bridge Works 803.4.2

Ministry of Road Transport and Highways - Specifications form Road And Bridge Works 803.4.2

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
803.4.1.2 (Flow resistance (BS 3262 (Part 1)))	1200.0
803.4.1.2 (Softening point (BS 3262 (Part 1)) ASTM D 36)	1200.0
803.4.1.2 (Cracking Resistance (BS 3262 (Part 1)))	1200.0
803.4.1.2 (Drying Time)	1200.0
803.4.1.2 (Luminance (Yellow))	1200.0
803.4.1.2 (Luminance (White) (Daylight luminance at 45 degrees))	1200.0
803.4.1.2 (Calcium carbonate and Inert fillers (BS 3262 (Part 1)))	1200.0
803.4.1.2 (Binder Content % by mass (BS 3262 (Part 1)))	1200.0
803.4.1.2 (Colour)	1200.0
803.4.1.2 (Titanium Dioxide, as TiO2 % by mass (BS 3262 (Part 1)))	1200.0
803.4.1.2 (Glass Bead content % (BS 3262 (Part 1)))	1200.0
803.4.2.3 (Free flowing properties)	900.0
803.4.2.3 (Roundness)	1000.0
803.4.2.3 (Gradation (Type 2) - below 180 micron(BS 6088))	1000.0
803.4.2.3 (Gradation (Type 2) - 180 micron (BS 6088))	500.0
803.4.2.3 (Gradation (Type 2) - 300 micron (BS 6088))	500.0
803.4.2.3 (Gradation (Type 2) - 600 micron (BS 6088))	500.0
803.4.2.3 (Gradation (Type 2) - 850 micron (BS 6088))	500.0
803.4.2.3 (Gradation (Type 1) - 180 micron (BS 6088))	750.0
803.4.2.3 (Gradation (Type 1) - 425 micron (BS 6088))	750.0
803.4.2.3 (Gradation (Type 1) - 850 micron (BS 6088))	750.0
803.4.2.3 (Gradation (Type 1) 1.18mm (BS 6088))	750.0
803.4.2.3 (Appearance)	100.0
Thermoplastic paint (Skid resistance (BS 6044))	1.0
Table 800-9 (Yellow Pigment)	1200.0
- (On-site testing of applied road marking material)	56000.0

537

IS 101 part 6 sec 1 (1988) - "METHODS OF SAMPLING AND TEST FOR PAINTS, VARNISHES AND RELATED PRODUCTS" SALT SPRAY FOR 96 HRS.

"METHODS OF SAMPLING AND TEST FOR PAINTS, VARNISHES AND RELATED PRODUCTS" SALT SPRAY FOR 96 HRS.

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 ()	-

538

ASTM B117 - Salt spray for 3000 hrs ASTM B117

Salt spray for 3000 hrs ASTM B117

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
ASTM B 117 (Salt Fog Test 5% Nacl solution(for 96 hrs) ASTM 117B/IEC 60512-11-6 AS PER CLAUSE NO. 7.4.9 FOR INTER VEHICULAR COUPLER UNIT 500AMP AS PER RDSO SPEC. NO. RDSO/PE/SPEC/AC/0177-(REV-01)-2013)	5000.0
1 ()	-

539

BS 3262(Part -1)1989 (1989) - Hot Applied Thermoplastic Road Marking Material

Hot Applied Thermoplastic Road Marking Material

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Hot Applied Thermoplastic road Marking Material (Aggergate together with pigment ,Extender and solid Glass beads % by mass of total mixture)	2200.0
Hot Applied Thermoplastic road Marking Material (Colour)	1000.0
Hot Applied Thermoplastic road Marking Material (Drying time)	1000.0
Hot Applied Thermoplastic road Marking Material (Cracking resistance at low temperature on application to concrete Block)	1200.0
Hot Applied Thermoplastic road Marking Material (Softening point)	1200.0
Hot Applied Thermoplastic road Marking Material (Flow Resistance)	1200.0
Hot Applied Thermoplastic road Marking Material (Solid Glass Bead content % by mass of total mixture)	1700.0
Hot Applied Thermoplastic road Marking Material (Luminance)	1500.0
Hot Applied Thermoplastic road Marking Material (Pigment as Titanium Dioxide (TiO2) % by mass of total mixture)	2000.0
Hot Applied Thermoplastic Road Marking Material (Binder Content (Resin and Oil), % by mass of total mixture)	2000.0

540

IS 3099 : Part 2 (1992) - Microscopes - Slips and slides: Specification: : Part 2 Microscope slides

Microscopes - Slips and slides: Specification: : Part 2 Microscope slides

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
10 (Marking)	200.0
9 (Packaging)	200.0
8 (Sampling)	200.0
7 (Edge Quality)	200.0
6 (Parallelism )	250.0
5 (Surface Finish )	200.0
4 (Visible Seed)	250.0
3.1 (Thickness )	500.0
3 ( Width)	500.0
3 (Length)	500.0
2.1 (Refractive Index)	1000.0