NTH - Management Information System

National Test House (ER), Kolkata

Block-C.P, Sector-V, Salt Lake City, Kolkata, West Bengal - 700091, Kolkata, Kolkata, West Bengal, 700091

- nthsal-wb[at]nic[dot]in

Scope List

Reset

1145 Results

S.No.

Standard No.

Product

Testing Charges (Excl. Of Taxes)

541

Custom moisture-coal tar - Custom moisture-coal tar

Custom moisture-coal tar

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Moisture, percent by mass)	1200.0

542

IS 1180 : Part 1 (2014) - Outdoor Type Oil Immersed Distribution Transformers - Specification Part 1 Mineral Oil Immersed (Fourth Revision) (1100 kVA to 2 500 kVA) [1100 kVA to 2 500 kVA]

Outdoor Type Oil Immersed Distribution Transformers - Specification Part 1 Mineral Oil Immersed (Fourth Revision) (1100 kVA to 2 500 kVA)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
21.2(a) (Measurement of Winding Resistance)	1000.0
21.2(b) (Measurement of voltage ratio and,check ofvoltage vector relationship)	2000.0
7.9 & 8.9 (Measurement of Permissible flux density and over fluxing)	20000.0
21.5.1.121.5.2.121.5.3.1 (Vacuum Pressure (Type Test))	20000.0
21.3(b) (Temperatur Rise Test)	40000.0
21.2(g) (Separate Source AC voltage withstand test)	2500.0
21.5.1.221.5.2.221.5.3.2 (Pressure test (routine))	5000.0
21.4.(d) (Adhesion by Tape Test)	5000.0
21.5.1.321.5.2.321.5.3.3 (Oil leakage test)	7000.0
21.4( c) (Measurement of No load current at 112.5 percent voltage)	2000.0
21.2(e) (Measurement of insulation resistance)	1500.0
21.2(c) (Measurement of impedance voltage (principal tapping), shortcurcuit impedance and load loss (At 50% and 100% load))	8000.0
21.2(d) (Measurement of no Load and loss and current)	6000.0
21.2(f) (lnduced Over Voltage withstand test)	4000.0
21.4(a) (Determination of sound levels)	7000.0
21.4( e) (BDV of Oil in the tranformer)	10000.0
21.5.1.121.5.2.121.5.3.1 (Air Pressure (Type test)-Deflection)	20000.0
21.5.2.1 (Permanent Deflection)	20000.0
21.4( e) (Break Down Voltage)	10000.0
21.2(f) (lnduced Over Voltage withstand test)	4000.0
21.2(d) (No Load loss and current)	6000.0
21.2(c) (Load Loss and % Impedance)	8000.0
21.2(e) (Insulation Resistance)	1500.0
21.4( c) (No load current)	2000.0
8.9 (flux density and over fluxing)	20000.0
7.9 (flux density and over fluxing)	10000.0
21.5.3.3 (Oil leakage test)	5000.0
21.2(g) (AC High Voltage Withstand Test)	2500.0
21.3(b) (Temperature Rise of Oil and Windings.)	40000.0
21.5.3.1 (Permanent Deflection)	6000.0
21.4(a) (Determination of sound levels)	7000.0
As per CBIP Pub No. 317 Cl. 3.17 (Magnetic Balance Test)	5000.0
As per CBIP Manual No. 317 Cl. (Harmonics of No-load Current)	15000.0
As per CBIP No. 317 Cl. 3.10 (Zero Sequence Impedance Measurement)	5000.0
As per CBIP No. 317 Cl. 3.10 (Magnetic Balance Test)	5000.0
N.A. (Unbalance Current)	5000.0
CBIP Publication no. 317 (Polarization Index)	2500.0

543

IRS:S63-2014 - PVC Insulated Underground, Unscreened Cable for Railway Signalling- Power Cable

PVC Insulated Underground, Unscreened Cable for Railway Signalling- Power Cable

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.6.1 (Physical tests for conductor-Dimension)	1000.0
5.6.2 (Physical tests for conductor-Annealing Test)	2000.0
5.6.3 (Physical tests for conductor-Test for correspondence of cores)	1000.0
5.7 (Conductor Resistance Test)	2000.0
5.8.1 (Test for Armour wires/strips/tapes-Dimension)	1000.0
5.8.2 (Test for Armour wires/strips/tapes- Tensile Strength and Percentage Elongation Test)	2000.0
5.8.3 (Test for Armour wires/strips/tapes-Torsion Test (for Round wires only))	1000.0
5.8.4 (Test for Armour wires/strips/tapes-Winding Test(For Galvanised strips only))	2000.0
5.8.5(i)(a) (Test for Armour wires/strips/tapes-Tests for mass of Zinc Coating)	1000.0
5.8.5(i)(b) (Test for Armour wires/strips/tapes-Tests for uniformity of Zinc Coating)	1000.0
5.8.6 (Test for Armour wires/strips/tapes-Resistivity Test)	2000.0
5.8.7 (Test for Armour wires/strips/tapes-Test for closeness of armour wires/strips)	1000.0
5.9 (Test for thickness of insulation and sheath)	1000.0
5.10.1(i) (Physical tests for insulation,inner & outer sheaths-Tensile strength and elongation at break)	2000.0
5.10.2 (Physical tests for insulation,inner & outer sheaths-Shrinkage Test)	1000.0
5.10.3 (Physical tests for insulation,inner & outer sheaths-Hot deformation test)	1000.0
5.10.4 (Physical tests for insulation,inner & outer sheaths-Loss of mass test)	2000.0
5.10.5 (Physical tests for insulation,inner & outer sheaths-Colour fastness to day-light exposure)	2000.0
5.10.6 (Physical tests for insulation,inner & outer sheaths-Colour fastness to water)	1000.0
5.10.7 (Physical tests for insulation,inner & outer sheaths-Bleeding and blooming Test)	1000.0
5.10.8 (Physical tests for insulation,inner & outer sheaths-Cold bend test)	2000.0
5.10.9 (Physical tests for insulation,inner & outer sheaths-Cold impact test)	2000.0
5.10.10 (Physical tests for insulation,inner & outer sheaths-Heat shock test)	2000.0
5.10.11 (Physical tests for insulation,inner & outer sheaths-Thermal stability test)	2000.0
5.10.12 (Physical tests for insulation,inner & outer sheaths-Specific Gravity test for PVC)	1000.0
5.11 (Flammability Test)	2000.0
5.12 (High Voltage Test)	3000.0
5.13 (Insulation resistance test)	2000.0
5.14.1 (Water immersion-AC Test)	3000.0
5.15 (Visual inspection test-)	1000.0
5.9 (Test for thickness of insulation and sheath)	1000.0

544

IS 2645:2003 (RA 2017) - Integral Waterproofing Compounds for Cement Mortar and Concrete-Specification

Integral Waterproofing Compounds for Cement Mortar and Concrete-Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
3.2.a. (Setting time -Initial)	500.0
3.2.b (Setting time-Final)	500.0
3.3.a (Compressive strength-3 days)	2000.0
3.3.b (Compressive strength-7 days)	2000.0
3.4 (Chloride content)	2000.0
- (Appearance)	1000.0
- (Bulk density)	1000.0
- (pH)	1000.0

545

IS 2645 (2003) - Integral waterproofing compounds for cement mortar and concrete - Specification (Second Revision)

Integral waterproofing compounds for cement mortar and concrete - Specification (Second Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
3.3.b (Compressive Strength-7days)	2000.0
3.3.a (Compressive Strength-3 days)	2000.0
3.2.b (Setting Time (Final Setting Time))	500.0
3.2.a (Setting Time (Initial Setting Time))	500.0

546

JIS D 5302-2004 - Lead Acid Batteries for Motorcycles

Lead Acid Batteries for Motorcycles

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
8.3.2 (Capacity (10 hour rate) for 1 sample)	10000.0
8.3.3 (High Rate Discharge for 1 sample)	10000.0
8.3.4 (Vibration resistance)	10000.0
Reference 1 (Heavy Load Life Duration)	60000.0
Reference 2 (Shallow Cycle Endurance)	60000.0
Reference 3 (Characteristics of Electrolyte Decrease)	30000.0
Reference 4 (Storage Characteristic Feature Test)	20000.0
8.3.1 (Dimensions)	1000.0

547

JISC 8702 : 2009 - Small- sized valve regulated lead-acid batteries

Small- sized valve regulated lead-acid batteries

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4 of JISC 8702-2:2009 (Dimensions)	500.0
5.1 of JISC 8702-1:2009 (Capacity at 20 hr rate)	20000.0
5.2 of JISC 8702-1:2009 (High rate discharge characteristics)	20000.0
5.3 of JISC 8702-1:2009 (Cycle service Endurance)	200000.0
5.4 of JISC 8702-1:2009 (Storage characteristic Test)	20000.0
5.5 of JISC 8702-1:2009 (Maximum permissible current Characteristic)	15000.0
5.6 of JISC 8702-1:2009 (Charge Acceptance characteristic after deep discharge.)	15000.0
5.7 of JISC 8702-1:2009 (Endurance in Trickle application)	100000.0
5.8 of JISC 8702-1:2009 (Endurance in trickle application at 40 Deg C)	130000.0
5.9.a of JISC 8702-1:2009 (Gas Emission Intensity I)	15000.0
5.10.a of JISC 8702-1:2009 (Gas recombinating characteristic - operation of vent valve)	15000.0
5.11 of JISC 8702-1:2009 (Vibration Resistance Characteristics)	15000.0
7.12 of JISC 8702-1:2009 (Shock Resistance Characteristics)	15000.0
7.1.b (Actual Capacity at the 1 hour discharge rate)	20000.0
5.10.b of JISC 8702-1:2009 (Gas recombinating characteristic - Liquid leakage resistance characteristics)	15000.0
5.9.b of JISC 8702-1:2009 (Gas emission intensity II)	15000.0

548

CQAL/637 :2006 - SPECIFICATION FOR BATTERY SECONDARY, LEAD ACID, LOW MAINTENANCE FOR MT PURPOSES

SPECIFICATION FOR BATTERY SECONDARY, LEAD ACID, LOW MAINTENANCE FOR MT PURPOSES

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
15.1 (Visual Examination)	1000.0
15.2 (Physical Examination)	1000.0
15.3 (Dimensions and Layout)	1000.0
15.4 (Marking)	1000.0
15.5 (Capacity (5-h rate))	5000.0
15.6.1 (High Rate Discharge at -15 degree C)	10000.0
15.6.3 (High Rate Discharge at Normal Temperature)	15000.0
15.7 (Robustness of Handle)	5000.0
15.8 (Charge Acceptance)	15000.0
15.9 (Air Pressure Test)	10000.0
15.10 (Life Cycle test)	100000.0
15.11 (Vibration Resistance)	10000.0
15.12 (Over Charge Endurance)	20000.0
15.13 (Strength of Terminal)	5000.0
15.14 (Robustness to Fastening)	5000.0
15.15 (Test for Dry Charged Battery)	10000.0
15.16 (High Voltage Test)	5000.0
15.17 (Retention of Charge)	15000.0
15.18 (Electrolyte Retention test)	5000.0

549

RDSO SPECIFICATION No. M&C/PCN/123/2018 (2018) - SPECIFICATION FOR HIGH PERFORM ANTI-CORROSION EPOXY COATING (TWO PACK)

SPECIFICATION FOR HIGH PERFORM ANTI-CORROSION EPOXY COATING (TWO PACK)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found

550

RDSO M&C/ PCN/ 100/ 2018 (2018) - Specification for Epoxy Cum Polyurethane Painting System (Two Pack) for the Exterior Painting of Railway Coaches

Specification for Epoxy Cum Polyurethane Painting System (Two Pack) for the Exterior Painting of Railway Coaches

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Chapter V/Cl. 3.2 (Viscosity (Efflux time by Ford cup No. 4 ) at 27 degree C)	1200.0
Chapter V/Cl. 3.2 (Fineness of grind)	1200.0
Chapter V/Cl. 3.2 (Theoretical Spreading rate)	1200.0
Chapter V/Cl. 3.2 (Pot life(After induction time)ii) 40 ± 2 Deg C)	2000.0
Chapter V/Cl. 3.2 (Pot life (After induction time) at i) 27 ± 2 Deg C)	1500.0
Chapter V/Cl. 3.2 (Abrasion resistance-1000 cycles)	3000.0
Chapter V/Cl. 3.2 (Humidity test.)	11000.0
Chapter V/Cl. 3.2 (Durability Tests : Accelerated weathering test)	110000.0
Chapter V/Cl. 3.2 (Accelerated Tests Resistance to water)	1500.0
Chapter V/Cl. 3.2 (Accelerated Tests Resistance to solvents)	1500.0
Chapter V/Cl. 3.2 (Accelerated Tests Resistance to oil)	1500.0
Chapter V/Cl. 3.2 (Accelerated Tests Resistance to 20% caustic potash (weight by volume))	1500.0
Chapter V/Cl. 3.2 (Accelerated Tests (a) Resistance to 30% Sulphuric acid (weight by volume))	1500.0
Chapter V/Cl. 3.2 (poly isocyanate, in hardener)	3000.0
Chapter V/Cl. 3.2 (Unreacted monomer)	3000.0
Chapter V/Cl. 3.2 (Gloss at 60 degree angle of incidence)	1200.0
Chapter V/Cl. 3.2 (Mass in Kg/10 litres)	1200.0
Chapter V/Cl. 3.2 (Keeping Properties for both the packs)	5000.0
Chapter V/Cl. 3.2 (Flash Point (b) Component B)	1200.0
Chapter V/Cl. 3.2 (Flash Point (a) Component A)	1200.0
Chapter V/Cl. 3.2 (Flexibility & Adhesion (6.25mm mandrel))	1200.0
Chapter V/Cl. 3.2 (Scratch hardness (1.5 Kg LOAD))	1200.0
Chapter V/Cl. 3.2 (Volume solids)	1200.0
Chapter V/Cl. 3.2 (Dry film thickness/Per coat)	1200.0
Chapter V/Cl. 3.2 (Colour)	1200.0
Chapter V/Cl. 3.2 (Finish)	1200.0
Chapter V/Cl. 3.2 (Consistency)	1200.0
Chapter V/Cl. 3.2 (Drying time c) Hard Dry at 70 Deg C)	1200.0
Chapter V/Cl. 3.2 (Drying time b) Hard Dry)	1200.0
Chapter V/Cl. 3.2 (Drying time a) Surface Dry)	1200.0
Chapter V/Cl. 3.2 (Identification of polyisocyanates)	3000.0
Chapter II/Cl. 4.1 (Protection against corrosion under condition of condensation)	9000.0
Chapter II/Cl. 4.1 (Resistance to salt spray)	21000.0

551

NTHER- Calibration of High Current Source (V/I Method) More than 100A - Calibration of High Current Source (V/I Method) More than 100A

Calibration of High Current Source (V/I Method) More than 100A

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
A.1 (Calibration of High Current Source (V/I Method) up to 500A (ac or dc))	4500.0
A.2 (Calibration of High Current Source (V/I Method) up to 800A (ac or dc))	5000.0
A.3 (Calibration of High Current Source (V/I Method) up to 1000A (ac or dc))	6000.0

552

ETI/OHE/50(6/97) re-designated to TI/SPC/OHE/CAT(Cu-Cd)/0971 (2021) - Technical specification for Cadmium copper conductors for over head Electric Traction

Technical specification for Cadmium copper conductors for over head Electric Traction

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
8.2.1 (Visual examination)	1000.0
8.2.2 (Chemical composition)	2000.0
8.2.3 (Measurement of diameter of individual wire and stranded conductor)	2000.0
8.2.4 (Measurement of weight of wire and conductor)	2000.0
8.2.5 (Measurement of lay length and lay ratio of each layer of stranded conductor)	5000.0
8.2.6 (Measurement of Electrical resistance of wire and stranded conductor)	15000.0
8.2.7 (Tensile test on wires)	32000.0
8.2.8 (Wrapping test on wires)	5000.0

553

NTHER-Calibration of Micro-ohm Meter - NTHER-Calibration of Micro-ohm Meter

NTHER-Calibration of Micro-ohm Meter

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
A1 (Calibration of Micro-ohm Meter(1A))	2000.0
A2 (Calibration of Micro-ohm Meter(100A))	3000.0

554

IS:14772-2000 (2000) - GE~NERAL REQUIREMENTS FOR ENCLOSURES FOR ACCESSORIES FOR HOUSEHOLD AND SIMILAR FIXED ELECTRICAL INSTALLATIONS - SPECIFICATION

GE~NERAL REQUIREMENTS FOR ENCLOSURES FOR ACCESSORIES FOR HOUSEHOLD AND SIMILAR FIXED ELECTRICAL INSTALLATIONS - SPECIFICATION

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
15 (RESISTANCE OF INSULATING MATERIAL TO ABNORMAL HEAT AND TO FIRE)	10000.0

555

IS 2250:1981 - Code of Practice for Preparation and use of Masonry Mortars

Code of Practice for Preparation and use of Masonry Mortars

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
2.4,6.1, Table 1 & Appendix A (Compressive strength of Masonry Mortar)	4000.0
9.1.1 Table 1,Appendix B (Consistency of Masonry Mortar)	500.0
6,Table 1 (Grade of Mortar-Mortar mix ratio (IS 1199))	5000.0

556

ND Custom 3 (2022) - Stainless Steel Wire 420 Grade

Stainless Steel Wire 420 Grade

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Tensile Strength)	3000.0
2 (Carbon)	500.0
2 (Manganese)	500.0
2 (Silicon)	500.0
2 (Phosphorus)	500.0
2 (Sulphur)	500.0
2 (Chromium)	500.0
2 (Nickel)	500.0

557

Custom BHU Soil

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (pH)	1000.0
2 (Manganese)	1000.0
3 (Zinc)	1000.0
4 (Total Nitrogen)	1000.0
5 (Iron)	1000.0

558

IS 1148 (2009) - Steel Rivet Bars (medium And High Tensile)--For Structural Purposes--For Structural Purposes

Steel Rivet Bars (medium And High Tensile)--For Structural Purposes--For Structural Purposes

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
13 (Shear Test (Medium Tensile Steel))	3000.0
9 (Diameter of Bar (Over 24mm))	500.0
6 (Carbon)	500.0
6 (Sulphur)	500.0
6 (Phosphorus)	500.0

559

CUSTOM-02-ER-MCALI - Calibration of Test Ring (Ketos)

Calibration of Test Ring (Ketos)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Dimension)	4000.0

560

IS 12118(Part 1):1987 - Specification for Two-Part Polysulphide-based Sealants

Specification for Two-Part Polysulphide-based Sealants

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.1.1.1 (Rheological Properties-Pouring grade sealants)	1000.0
5.1.1.2 (Rheological Properties-Gun grade sealant)	5000.0
5.1.2 (Plastic deformation)	1500.0
5.1.3 (Adhesion and Tensile modulus)	5000.0
5.1.5 (Adhesion in Peel)	2500.0
5.1.6 (Loss of Mass after heat ageing)	1500.0
5.1.7 (Staining)	600.0
5.1.4 (Application life)	1500.0

561

ASTM A572 (2007) - Standard Specification for High-Strength Low-Alloy Columbium-Vanadium Structural Steel

Standard Specification for High-Strength Low-Alloy Columbium-Vanadium Structural Steel

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6 (Yield Point)	2000.0
6 (Tensile Strength)	2000.0
6 (Elongation)	1000.0

562

IS 2590 - SPECIFICATION FOR PRIMARY ALUMINIUM INGOTS FOR REMELTING FOR GENERAL ENGINEERING PURPOSES

SPECIFICATION FOR PRIMARY ALUMINIUM INGOTS FOR REMELTING FOR GENERAL ENGINEERING PURPOSES

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6.1 i (Aluminium,)	1200.0
6.1 ii (Copper)	1200.0
6.1 iii (Silicon)	1200.0
6.1 iv (Iron)	1200.0
6.1 v (Manganese)	1200.0
vi (Zinc)	1200.0
6.1 vii (Titanium + Vanadium)	2400.0

563

IS 5666 (1970 RA 2019) - Etch Primer

Etch Primer

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
3.3 (Consistency)	1000.0
3.3.2. (Mixed Material)	500.0
3.4 (Viscosity)	1000.0
3.5.1 (Air Drying)	500.0
3.5.2 (Force Drying Force Dry for 15 min at temp 85 to 100 Deg c &allow to cool for 1 hrs at Room Temp)	500.0
3.6 (Finish)	200.0
3.7 (Fineness of Dispersion)	500.0
3.8 (Fitness to Take a Coat of Primer, Cellulose Finish)	500.0
3.9 (Keeping Quality (for Six Months))	4000.0

564

Customized IS:11673-1992 (1992) - Sodium Hypo Chlorite Specification

Sodium Hypo Chlorite Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.3 (Available Chlorine % by mass by Volume)	2000.0

565

IS 14246 (2024) - Continuously Pre-Painted Galvanized Steel Sheets and Strips

Continuously Pre-Painted Galvanized Steel Sheets and Strips

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6.2 (Bend Test)	1000.0
9 (Mass of Sheet)	1000.0
8 (SALT SPRAY TEST (CORROSION RESISTANCE))	50000.0
4.2 (Mass of Zinc Coating)	2000.0
4.3 (Paint Coating Thickness)	2000.0
6.3 (Pencil Hardness Test)	1000.0
6.4 (Impact Resistance Test)	1000.0
6.5 (Cross Hatch Test)	1000.0
4 (Chemical Analysis as per Is 513 (Part-1):2016)	2500.0
4 (Tensile strength, MPa)	1000.0
4 (Yield Stress, MPa)	1000.0
4 (% Elongation)	1000.0
9 (Base Metal Thickness)	500.0
9 (Total Coated Thickness (as on received))	500.0

566

EURAMET cg-2 (2011) - CALIBRATION OF GAUGE BLOCK COMPARATORS

CALIBRATION OF GAUGE BLOCK COMPARATORS

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5 (Length)	15000.0

567

Custom equaliser valve upper casing - Equaliser valve upper casing

Equaliser valve upper casing

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Carbon %)	1000.0
2 (Manganese %)	1000.0
3 (Silicon %)	1000.0
4 (Chromium %)	1000.0
5 (Nickel %)	1000.0
6 (Copper %)	1000.0
7 (Magnesium %)	1000.0

568

FCO 1985 (as amended upto November 2023) - FCO 1985 (as amended upto October 2024)

FCO 1985 (as amended upto October 2024)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Total Nitrogen)	1000.0
2 (Ammoniacal Nitrogen)	1000.0
3 (Nitrate Nitrogen)	1000.0
4 (Urea Nitrogen)	1000.0
5 (Total phosphorous (as P2O5) percent by weight)	1000.0
6 (Water soluble phosphorous (as P2O5) percent by weight)	1000.0
7 (Available phosphorous (as P2O5) percent by weight)	1000.0
8 (Moisture percent by weight)	1000.0
9 (Sulphate Sulphur (as S))	1000.0
10 (Elemental Sulphur (as S) percent by weight)	1000.0
11 (Total elemental sulphur (as S), percent by weight)	1000.0
12 (Free acidity (as H2SO4) percent by weight)	1000.0
12 (Water soluble potassium as K2O, Percent by weight)	1000.0
13 (Particle size -material retained between 1mm and 4mm IS sieve)	1000.0
14 (Total Sulphur , Percent by weight)	1000.0
15 (Calcium Nitrate, Percent by weight)	1000.0
16 (Free phosphoric acid (as P2O5) percent by weight)	1000.0
17 (Magnesium as Mg , percent by weight)	1000.0
18 (Magnesium as MgO , percent by weight)	1000.0
19 (Magnesium as MgCl2, percent by weight)	1000.0
20 (Sodium as NaCl percent by weight)	1000.0
21 (Total Chlorides, as Cl percent by weight)	1000.0
22 (Matter insoluble in water, percent by weight)	1000.0
23 (pH of 5% solution)	1000.0
24 (As as As % by weight)	1000.0
25 (As as As2O3, % by weight)	1000.0
26 (Specific gravity at given temperature)	1000.0
27 (Biuret % by weight)	1000.0
28 (Particle size, percent retained between given IS sieves)	1000.0
29 (Manganese as Mn % by weight)	1000.0
30 (Zinc as Zn % by weight)	1000.0
31 (Zinc as Zn % by weight in the form of Zn EDTA)	1000.0
32 (Zinc as Zn % by weight in the form of Zn HEDP)	1000.0
33 (Iron/Fe as Fe % by weight in the form of FeHEDP)	1000.0
35 (Lead as Pb % by weight)	1000.0
36 (Cadmium as Cd % by weight)	1000.0
37 (Copper as Cu % by weight)	1000.0
38 (Iron as Fe % by weight)	1000.0
39 (Boron as B % by weight)	1000.0
40 (Calcium as Ca % by weight)	1000.0
12.1 (Molybdenum)	1000.0
55 (Fe as Fe-EDTA)	1000.0
56 (Appearance)	1000.0
1 (Total Nitrogen(ammoniacal and Urea)percent by weight)	1000.0
15 (Particle size-Minimum 90% of material shall be retained between 1mm and 4 mm IS sieve)	1000.0
1 (Carbon (% by mass))	1000.0
1 (Carbon : NItrogen ratio (C: N))	1000.0
1 (Bulk density)	1200.0
1 (Total organic carbon)	1200.0
1 (Manganese as Mn (% by mass))	1200.0
1 (Contamination level)	1200.0
1 (Efficiency Character)	1200.0
0 (Available Phosphorus (as P2O5),)	1000.0

569

IS 1321 : Part 1 (2003) - Sisal ropes – Specification Part 1 Untarred varieties (fourth revision)

Sisal ropes – Specification Part 1 Untarred varieties (fourth revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.1 (Identification of Fiber)	2000.0
5.2 (Count of the Yarn)	1000.0
5.3 (No of Yarns per Strand)	500.0
5.3 (Lay of Strand)	500.0
5.4 (No. of Strands in the Rope)	500.0
5.4 (Lay of Rope)	500.0
5.4.1 (Angle of Lay)	1000.0
5.5 (Percentage of Lubricant)	2000.0
5.6 (Zinc Content)	1000.0
5.6 (Copper Content.)	1000.0
6.1 (Mass of the Coil)	1000.0
6.2 (Pitch)	1000.0
6.3 (Length of the Coil)	1000.0
6.4 (Linear Density of Rope)	1000.0
6.4 (Breaking Strength Of Rope)	5000.0
6.5 (Diameter of Rope)	500.0

570

Custom-24-ER-LM - Pull out Test for Assembly

Pull out Test for Assembly

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Pull out Test for Assembly)	5000.0