NTH - Management Information System

National Test House (ER), Kolkata

Block-C.P, Sector-V, Salt Lake City, Kolkata, West Bengal - 700091, Kolkata, Kolkata, West Bengal, 700091

- nthsal-wb[at]nic[dot]in

Scope List

Reset

1145 Results

S.No.

Standard No.

Product

Testing Charges (Excl. Of Taxes)

781

DKD-R 6-1 (2014) - Calibration of Pressure Gauges

Calibration of Pressure Gauges

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7 (Pressure)	4000.0

782

OIML R 76-1 (2006) - Non-automatic weighing instruments Part 1: Metrological and technical requirements - Tests

Non-automatic weighing instruments Part 1: Metrological and technical requirements - Tests

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
3 (Weighing balance calibration)	4000.0
3 (Weight)	4000.0

783

OIML R 111-1 (2004) - Weights of classes E1, E2, F1, F2, M1, M1–2, M2, M2–3 and M3 Part 1: Metrological and technical requirements

Weights of classes E1, E2, F1, F2, M1, M1–2, M2, M2–3 and M3 Part 1: Metrological and technical requirements

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5 (Mass (1mg to 200g))	4000.0
5 (Mass (500g-5kg))	4000.0
5 (Mass)	4000.0
5 (Mass, g)	1200.0

784

Custom-5-NTH-LM - Wire Mesh Panel

Wire Mesh Panel

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Width)	200.0
2 (Height)	200.0
3 (Bend Test)	1000.0
4 (Panel Weight)	500.0
5 (Tensile Strength of wire)	3000.0
6 (Weld Shear Strength)	9000.0
7 (Mass of Zinc Coating)	1000.0
8 (Powder Coating Thickness)	2000.0
9 (Salt Spray Test for 1000 Hours)	50000.0
18 (Sulphur + Phosphorus)	500.0
18 (Phosphorus)	500.0
17 (Sulphur)	500.0
16 (Carbon)	500.0
15 (Elongation of wire)	1000.0
14 (Yield Stress of wire)	1000.0
13 (Ultimate Tensile Strength of wire)	1000.0
12 (Unit Weight)	500.0
11 (Mesh Size (c/c))	300.0
10 (Diameter of Wire)	500.0
19 (Uniformity of Coating)	500.0

785

Custom-4-NTH-LM - Omega Clamp/Profile Plate

Omega Clamp/Profile Plate

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Length)	500.0
2 (Width)	500.0
3 (Thickness)	500.0
4 (Weight)	1000.0
5 (Mass of Zinc Coating)	1000.0
6 (Uniformity of Coating)	500.0
7 (Powder Coating Thickness)	1000.0
8 (Salt Spray Test for 1440 Hours)	72000.0

786

Custom-3-NTH-LM - Concertina coil/PTCC

Concertina coil/PTCC

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Diameter of wire, mm)	1000.0
2 (Blade Length)	1000.0
3 (Center to center distance between blade)	1000.0
4 (Thickness of Blade)	1000.0
5 (Tensile Strength of wire)	3000.0
6 (Yield Stress of wire)	1000.0
7 (Percentage Elongation of wire)	1000.0
8 (Carbon)	500.0
8 (Sulphur)	500.0
8 (Phosphorus)	500.0
8 (Chromium)	1000.0
8 (Manganese)	500.0
8 (Nickel)	500.0
8 (Silicon)	500.0
9 (Mass of Zinc Coating of wire)	1000.0
11 (Unit Weight)	1000.0

787

Custom-2-NTH-LM - Straining/Intermediate Y arm

Straining/Intermediate Y arm

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Leg Length)	500.0
2 (Thickness)	500.0
3 (General Dimensions)	1000.0
4 (Tensile Strength)	1500.0
5 (Yield Strength)	1500.0
6 (Percentage Elongation)	1000.0
8 (Mass of Zinc coating)	1000.0
9 (Uniformity of coating)	500.0
10 (Powder Coating)	1000.0
7 (Carbon)	500.0
7 (Sulphur)	500.0
7 (Phosphorus)	500.0
7 (Manganese)	500.0
7 (Silicon)	500.0
7 (Carbon equivalent)	500.0
11 (Salt Spray Test for 1440 Hours)	72000.0

788

Custom-1-NTH-LM - Fence Post Hollow Section and Fence Post Support Strip

Fence Post Hollow Section and Fence Post Support Strip

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Dimension of Post)	1000.0
2 (Thickness)	500.0
3 (Nominal Mass)	1000.0
4 (Tensile Strength)	1000.0
5 (Yield Strength)	1000.0
6 (Percentage Elongation at 5.65 √area)	1000.0
7 (Mass of Zinc Coating)	1000.0
8 (Uniformity of coating)	500.0
9 (Powder coating thickness)	1000.0
10 (Salt Spray Test for 1440 Hours)	72000.0

789

BS 476 part 7 (1997) - Classification of Surface spread of flame of products

Classification of Surface spread of flame of products

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Surface Spread of flame test ( BS 476 Part 7))	8000.0

790

Chemical Paint Lab NTH ER Custom Specification (2022) - Chemical Paint Lab NTH ER Custom Specification

Chemical Paint Lab NTH ER Custom Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5 (Description)	100.0
2 (Adhesion by tape test (Cross Hatch) ASTM D-3359)	1000.0
3 (Adhesion Pull off strength ASTM D 4541)	5000.0
1 (Dry Film Thickness (as per ASTM D -7091) Non destructive Measurements)	1000.0
4 (MEK rub test (ASTM D 4752))	500.0

791

NCD 1427 Issue 1 - Specification for mineral wool marine board for thermal & acoustic insulation

Specification for mineral wool marine board for thermal & acoustic insulation

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Appendix A , Clause No 2.1 (Weight of Glass Cloth Facing)	1000.0
Appendix A , Clause No 2.2 (Thickness of Glass Cloth Facing)	1000.0
Appendix A , Clause No 2.3.1 (Warp ends/10cm)	1000.0
Appendix A , Clause No 2.3.2 (Weft ends/10cm)	1000.0
Appendix A , Clause 2.5.1 (Breaking Strength (Warp))	2000.0
Appendix A, Clause- 2.5.2 (Breaking Strength (Weft))	2000.0
Appendix A, Clause-3 (Ability to Bend)	1000.0
Appendix B, Table -B1(a) (Percent Alkalinity (As Na2O))	1000.0
Appendix B, Table -B1(b)(i) (Compression)	2000.0
Appendix B,Table (b) (ii) (Recovery)	1000.0
Appendix B ,Table-B1(C) (Puncture Resistance)	2000.0
Appendix B ,Table-B1(d) (Inter laminar Adhesion)	2000.0
Appendix B ,Table-B1(e) (Water Absorption)	2000.0
Appendix B ,Table-B1(f) (Shot Content)	2000.0
Appendix B ,Table-B1(l) (Surface Spread of Flame)	8000.0
Appendix C, 3(g) (Initial Tack Test)	2000.0
Appendix C, 3(h) (Bond Strength)	2000.0
7.0 (Thickness of Finished Boards)	1000.0
7.0 (Length of finished Boards)	500.0
7.0 (Width of Finished Boards)	500.0
8.0 (Weight of Finished Boards)	1000.0
9.0 (Freedom from Defects)	500.0

792

Custom-35-ER - False Ceiling and Accessories

False Ceiling and Accessories

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Dimension (Thickness))	1000.0
2 (Dimension (Diameter))	1000.0
3 (Dimension (length))	1000.0
4 (Mass of Zinc Coating)	2000.0
6 (Dimension (Size))	1000.0
7 (Dimension (Perforation Dia))	1000.0
8 (Dimension(Height of Tiles))	1000.0
13.2 First Characteristic Numeral 2 (Protection against solid foreign objects of 12.5 mm dia and greater,First Characteristic Numeral 2)	7500.0
14.2.3 second characteristic numeral 3 (14.2.3 second characteristic numeral 3:Protected against spraying water)	7500.0
14.2.4 Second characteristic numeral 4 (14.2.4 Second characteristic numeral 4 :Protected against splashing water)	7500.0
4.2 (Material : Messenger Conductor)	100.0
27358 (Material : Insulation)	100.0
6.3 (Weight of Phosphate Coating)	2000.0
6.11(ix) (Accelerated storage stability)	100.0
9 (Carbon)	500.0
9 (Sulphur)	500.0
9 (Phosphorus)	500.0
9 (Manganese)	1000.0
9 (Nickel)	1000.0
9 (Silicon)	1000.0
13 (Perforation Dia of Tiles)	1000.0
12 (Powder Coating Thickness of Tiles)	2000.0
11 (Size of Tiles)	1000.0
10 (Thickness of Tiles)	500.0

793

RDSO/2013/CG-01 (2023) - Non-Asbestos Based Organic Brake Pads for LHB Type Coaches Equipped with Disc Brake System on Indian Railways

Non-Asbestos Based Organic Brake Pads for LHB Type Coaches Equipped with Disc Brake System on Indian Railways

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
9.0 (Bending Strength)	3000.0
9.0 (Density)	1000.0
9.0 (Ash Content)	1000.0
9.0 (Acetone extract)	2000.0
9.0 (Cross braking strength)	2000.0

794

13620 (1993) - FUSION BONDED EPOXY COATED REINFORCING BARS-SPECIFICATION

FUSION BONDED EPOXY COATED REINFORCING BARS-SPECIFICATION

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
A-5 (BOND STRENGTH TO CONCRETE(A-5))	15000.0

795

13620 (upto 12mm) (1993) - FUSION BONDED EPOXY COATED REINFORCING BARS-SPECIFICATION (Upto 12mm)

FUSION BONDED EPOXY COATED REINFORCING BARS-SPECIFICATION (Upto 12mm)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
A-5 (BOND STRENGTH TO CONCRETE (IS 13620:1993))	10000.0

796

SLS 1126.1-2020 - Specification for Lead-Acid Starter Batteries[ Part 1: General Requirements & Method of Test]

Specification for Lead-Acid Starter Batteries[ Part 1: General Requirements & Method of Test]

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
9.1 (1st 20 h capacity Test)	25000.0
9.2 (1st Reserve Capacity Test)	20000.0
9.4 (Charge Acceptance Test)	15000.0
9.5 (charge retention test)	20000.0
9.6.1.1 (Corrosion Test)	15000.0
9.6.2 (Endurance in cycle test)	45000.0
9.7 (Water consumption Test)	15000.0
9.8 (Vibration Resistance Test)	15000.0
9.9 (Electrolyte Retention Test)	10000.0
8.4.2,9.10 (Cranking performance for dry charge batteries)	15000.0
9.6.1.2 (Endurance in cycle test)	55000.0
9.1 (2nd 20 h capacity Test)	25000.0
9.1 (3rd 20 h capacity Test)	25000.0
9.2 (2nd Reserve Capacity Test)	20000.0
9.2 (3rd Reserve Capacity Test)	20000.0
9.3.1 (2nd cranking performance test)	20000.0
9.3.1 (3rd cranking performance test)	20000.0

797

8623-1:(1993) - Low-Voltage Switchgear and Control gear Assemblies, Part 1: Requirements for Type-Tested and Partially Type-Tested Assemblies [ETD 7: Low Voltage Switchgear and Control gear]

Low-Voltage Switchgear and Control gear Assemblies, Part 1: Requirements for Type-Tested and Partially Type-Tested Assemblies [ETD 7: Low Voltage Switchgear and Control gear]

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
8.2.2 (Verification of dielectric properties)	10000.0
8.3.4 (Verification of insulation resistance)	10000.0
8.2.1.3 (Tempreture rise test)	20000.0

798

JIS D 5301:2006 - Lead Acid starter Batteries

Lead Acid starter Batteries

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
9.5.2 (5 h rate capacity)	20000.0
Annexure 1 Clause 2 (Water consumption test)	10000.0
10.1 (20 h rate capacity (C20) test)	25000.0
10.2 (Reserve capacity test)	20000.0
10.3 (Cold cranking ampere test)	15000.0
10.4 (Charge acceptance test)	10000.0
10.5(a) (Light load endurance test)	25000.0
10.5(b) (Heavy load endurance test)	25000.0
10.6 (Vibration resistance)	10000.0
10.7 (Terminal strength test)	5000.0
10.8 (Fastening robustness test)	5000.0
10.9 (Electrolyte retention test)	20000.0
10.10 (Charge retention test)	15000.0
Annex A, Table A.2 (Dimension)	5000.0

799

GE: IRS -2 (Final) (2005) - SPECIFICATION FOR MECHANICALLY PRODUCED BLANKETING MATERIAL FOR RAILWAY FORMATIONS INCLUDING GUIDELINES FOR LAYING

SPECIFICATION FOR MECHANICALLY PRODUCED BLANKETING MATERIAL FOR RAILWAY FORMATIONS INCLUDING GUIDELINES FOR LAYING

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4.1.C.1 (Test for Non Plastic fines(Particles of size less than 75 micron)(as per GE: IRS -2 (Final)))	1000.0
4.1.C.2 (Test for Plastic fines(GE: IRS -2 (Final)))	1000.0
4.1.d (Test for Particle size distribution(GE: IRS -2 (Final)))	5000.0
4.1.e.1 (Test for Uniformity Co-efficient (Cu) {GE: IRS -2 (Final)})	1500.0
4.1.e.2 (Test for Co-efficient of Curvature(CC) (GE: IRS -2 (Final)))	1500.0
Nil (Liquid Limit (IS 2720(5)-1985))	1000.0
- (Plastic limit (IS 2720(5):1985))	1000.0
- (Free soil Index(IS 2720(40)1977))	1000.0
- (Shrinkage limit (IS 2720(6)1985))	1000.0
- (DETERMINATION OF WATER CONTENT-DRY DENSITY RELATION (IS 2720(8):1983) (Proctor test))	5000.0
- (Test for Aggregate Abrasion Value (Los Angeles) as per IS 2386 (Part 4): 1963)	1500.0

800

customer specification ER CHEMICAL METAL LAB (2022) - customer specification ER CHEMICAL METAL LAB

customer specification ER CHEMICAL METAL LAB

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Zinc (as Zn),% by mass)	2000.0
2 (Aluminum as Al % by mass)	2000.0

801

RDSO/PE/SPEC/AC/0059-2004(Rev.O),Amendment No-01 (2004) - V-Belts used For Driving Alternators For TL and AC Coaches

V-Belts used For Driving Alternators For TL and AC Coaches

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6.0 (Pitch length)	5000.0
7.0 (Coding)	1000.0
3.1 (Construction)	2000.0
3.2(i) (Hardness(IRHD))	1000.0
3.2(ii) (Tensile Strength of base material)	2000.0
3.2(iii) (Elongation at break of base material)	1000.0
3.3(i) (Elongation of Finished Belt)	1000.0
3.3(ii) (Reference Elongation at 300 kgf of Finished Belt)	1000.0
3.3(iii) (Breaking Strength)	2000.0
5.1(i) (Nominal Top width)	1000.0
5.1(ii) (Nominal Thickness)	1000.0
5.1(iii) (Angle)	1000.0
12.7(i) (Change in Hardness after ageing)	1000.0
12.7(ii) (Change in Tensile Strength after ageing)	2000.0
12.7(iii) (Change in elongation after ageing)	1000.0
12.7(iv) (Compression set)	1000.0

802

IS 542 (2018) - Coconut oil - Specification (Third Revision)

Coconut oil - Specification (Third Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.2.1 (Clarity)	500.0
5.7 (i) (moisture and insoluble impurities)	500.0
5.7(ii) (colour in lovibond scale)	500.0
5.7(iii) (Refractive index 40 dg)	500.0
5.7(iv) (Specific gravity 30 dg)	500.0
5.7 (v) (saponification value)	500.0
5.7(vi) (Iodine value)	500.0
5.7 (vii) (Acid value)	500.0
5.7(viii) (Unsaponifiable matter)	500.0
5.7 (ix) (Polenske value)	500.0
5.3 (Test for presence of Karanja oil)	500.0
5.3 (Test for presence of Kusum oil and other oils containing cyanogenic compounds)	500.0
5.3 (Test for presence of Castor oil)	500.0
5.3 (Test for presence of Hydrocyanic acid)	500.0
5.3 (Test for presence of Argemone oil)	500.0
5.3 (Test for presence of mineral oil)	500.0
5.3 (Test for presence of neem oil)	500.0

803

IS 4351 (2003) - STEEL DOOR FRAMES — SPECIFICATION

STEEL DOOR FRAMES — SPECIFICATION

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6.1 (Dimensions)	2000.0

804

Custom Paper Test (2022) - Method of Test for Paper on the lines of IS 1060

Method of Test for Paper on the lines of IS 1060

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Tests)	2000.0

805

IS 2214 : 1977 (1977) - Specification for Silver Nitrate , Pure and analytical Reagent

Specification for Silver Nitrate , Pure and analytical Reagent

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
3.2 (Silver Nitrate ( AgNO3) Percent/Mass)	2000.0

806

IS 15489 : 2013 NTH ER (2013) - PAINT, PLASTIC EMULSION — SPECIFICATION

PAINT, PLASTIC EMULSION — SPECIFICATION

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6.1 (Composition)	700.0
6.2 (Conditions in the Container)	600.0
6.3 (Thinning)	600.0
6.4 (Application Properties)	600.0
6.5 (Mass in kg/10 litre)	700.0
6.6 (Opacity)	700.0
6.7 (Fastness to Light (Xenon Arc apparatus for 500 hrs))	25000.0
6.8 .1.1 (C-2 Durability Test (Normal Outdoor Exposure Test 12 Months ) for Exterior Use Only)	10000.0
6.8 1.2 &6.8.2 (C-3 Durability Test ACCELERATED WEATHERING TEST Accelerated Weathering Apparatus QUV for 21 days UV condensation type)	18000.0
6.9 (Lead Restriction)	700.0
6.10 (Keeping Properties (For 12 months))	5000.0
6.11 (i) Table 1 (Consistency)	700.0
6.11(ii) Table 1 (Drying time, a) Surface Dry)	400.0
6.11(ii) Table 1 (Drying time b) Hard dry)	400.0
6.11 (iii) Table 1 (Finish)	700.0
6.11 (iv) (Gloss at 60 Deg. Angle)	700.0
6.11(v) Table 1 (Colour)	300.0
6.11(vii) Table 1 (Resistance to alkali)	700.0
6.11 (viii) Table 1 (Washability and cleanability)	700.0
6.11 (x) Table 1 (Recoating properties)	200.0
6.12.2 Specific requirements VOC (Volatile Organic Compounds (VOC) % by mass)	2400.0
6.12 .2 Toxic metals (toxic metals such as lead, cadmium, chomium (VI) and their compounds)	2400.0
3.1.1 (Volatile Organic Compound (gm/litre))	3000.0

807

IS 4277 (2014) - Sunflower oil - Specification (Second Revision)

Sunflower oil - Specification (Second Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.7(i) (moisture and insoluble impurities)	500.0
5.7.(ii) (colour in lovibond scale)	500.0
5.7(iii) (Refractive index 40 dg)	500.0
5.7(iv) (saponification value)	500.0
5.7(v) (Iodine value)	500.0
5.7(vi) (Acid value)	500.0
5.7(vii) (Unsaponifiable matter)	500.0
5.2 (Peroxide value)	500.0
5.8.1.3 (Limits for toxic metals, Lead)	500.0
5.8.1.3 (Limits for toxic metals, Arsenic)	500.0
5.8.1.3 (Limits for toxic metals, Cadmium)	500.0
5.8.1.3 (Limits for toxic metals, Mercury)	500.0
5.3 (Test for presence of neem oil)	500.0
5.3 (Test for presence of Castor oil)	500.0
5.3 (Test for presence of Kusum oil and other oils containing cyanogenic compounds)	500.0
5.3 (Test for presence of mineral oil)	500.0
5.3 (Test for presence of Hydrocyanic acid)	500.0
5.3 (Test for presence of Argemone oil)	500.0
5.3 (Test for presence of Karanja oil)	500.0
5.2 (freedom from adulterants, sediments, suspended particles,foreign matter etc)	500.0

808

Custom/Rubber/2022 (2022) - General Rubber Product

General Rubber Product

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
3.4 of IS 3400 Part-1 (Tensile Strength)	2000.0
3.5 of IS 3400 Part-1 (Elongation at Break)	1000.0
Firm's request. (Tensile strength After Ageing)	2000.0
3.0 of IS 3400 Part-IX (Relative Density)	1000.0
2.2 of IS 3400 Part-3 (Abrasion Loss)	2000.0
9.2 of IS 1891 Part-5 (Flame Test)	4000.0
Firm's request (Hardness (Shore A))	1000.0
Firm's request. (Water Immersion Test(Change in Weight))	2000.0
Firm's request. (Compression Set)	3000.0
Firm's request. (Compression Load Test at 125 Ton)	5000.0
Firm's request. (Hardness After Ageing(Shore A))	2000.0
Firm's request. (Elongation at break(After Ageing))	1000.0
Firm's request (Ash Content(%))	2000.0
Firm's request (Effect of Liquid Resistance in 33% HCL for 72 hrs at room temp)	2000.0
Firm's request (Dimensions)	1000.0

809

Dynamometer (4000kg) - Calibration of Dynamometer (4000kg)

Calibration of Dynamometer (4000kg)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Force)	15000.0

810

Dynamometer (3000kg) - Calibration of Dynamometer (3000kg)

Calibration of Dynamometer (3000kg)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Force)	15000.0